TELEDYNE API Everywhereyoulook 480H User Manual Download Page 55

Page: 55 / 57

09421A DCN8343

Teledyne API Model 480H O

Monitor User Manual

8.2.4.2. P

RESSURE

•

The exhaust line is connected to a vacuum source. Disconnect exhaust line

and see if pressure returns to specified range.

•

The pressure sensor has failed or drifted. Contact Teledyne API Technical

Spport for assistance.

8.2.5. TECHNICAL ASSISTANCE

If this manual does not solve your problems, technical assistance may be obtained

from:

Teledyne API, Technical Support

9970 Carroll Canyon Road

San Diego, California 92131-1106 USA

Toll-free Phone:

+1 800-324-5190

Phone:

+1 858-657-9800

Fax:

+1 858-657-9816

Email:

[email protected]

Website:

http://www.Teledyne-API.com

Summary of Contents for Everywhereyoulook 480H


























































Search results

Summary of Contents for Everywhereyoulook 480H

Reviews:

Related manuals for Everywhereyoulook 480H

Brands by name

Popular brands

TELEDYNE API Everywhereyoulook 480H, User Manual

Search results

Summary of Contents for Everywhereyoulook 480H

Reviews:

Related manuals for Everywhereyoulook 480H

Brands by name

Popular brands