Telect GMTXX Installation Manual Download Page 11 | Manualshive

Page: 11 / 22

Telect GMTXX Installation Manual Download Page 11

© Telect, Inc., All Rights Reserved, 132152-12 A0
1.509.926.6000 :: telect.com

9

100A/60A Universal Voltage GMT Fuse Panels
With Enhanced Power/Fuse & Bay Alarms

Power

:: HPGMTXX & GMTXX

Figure 6 - Input Connections on a 100A Panel

ALERT

!

ALERT! Only service personnel may replace fuses. The installer must verify that a readily accessible
protection device is incorporated in the building wiring feeding the fuse panel: 125A (max.) protection
device for a 100A panel; 75A (max.) for a 60A panel.

For input wiring on a 60A panel —

a. Strip off about 3⁄4 in. (10 mm) of insulation at end of input conductors (min. #6 AWG for a 60A feed).

b. If desired (highly recommended), lightly coat anti-oxidant on the bare conductor.

c. Insert the bare conductor into the barrel connector as indicated in the illustration, and then tighten the

screw to 16 in.-lb (1.8 N•m), max.

DO NOT REMOVE CAPS*

* Screws located below caps are used for

installing internal wiring at the factory.

Figure 7 - Input Connections on a 60A Panel

«
...
9
10
11
12
13
...
»

Summary of Contents for GMTXX























Reviews:

No comments