Tektronix RMD5000 Instructions Manual Download | Manualshive

Page: 13 / 23

background image

Installation Instructions

4.

Install the top support plate; note the orientation for the different instruments:
(See Figure 8.)

For DPO4000B instruments, install the top support plate with the

fl

ange

toward the front of the enclosure so that the “DPO4000B” stamping on the
plate is visible.

For DPO5000 instruments, install the top support plate with the

fl

ange toward

the back of the enclosure.

Figure 8: Installing the top support plate

RMD5000 Rackmount Kit Instructions

11

«
...
11
12
13
14
15
...
»

Summary of Contents for RMD5000
























Reviews:

No comments

Related manuals for RMD5000

Brand: U-Line Pages: 6

Brand: U-Line Pages: 6

Brand: Costway Pages: 4

PACKOUT 48-22-8481

Brand: Milwaukee Pages: 2

Brand: CHIEF Pages: 12

FPMA-D550DBLACK

Brand: NewStar Pages: 4

Brand: CHIEF Pages: 8

Brand: Mustang Pages: 5

Brand: ETC Pages: 3

Brand: HAGOR Pages: 16

Brand: GABOR Pages: 12

Brand: NCR Pages: 5

Brand: Yealink Pages: 8

Brand: CHIEF Pages: 1

Brand: Mount-It! Pages: 9

Brand: Konig & Meyer Pages: 6

Brand: Frigidaire Pages: 20

Brand: Konig & Meyer Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands