manualshive.com logo in svg

Tektronix Phaser 440, Service Manual

The Tektronix Phaser 440 provides exceptional printing proficiency. To ensure optimal utilization, a comprehensive Service Manual is available for free download from manualshive.com. This manual equips users with detailed instructions, troubleshooting techniques, and maintenance tips, enhancing their experience with this high-performance product.

Share
Download
background image

Service Manual

2-9

Installing the Printer and Drivers

2

Cabling the printer

Note

Carry spare serial and parallel cables.

  You can use them if you 

encounter a defective cable or as an alternate means of testing the 
printer-to-host communications. 

This topic explains making a hardware connection between a Phaser 440 and its 
host computer, setting the communication parameters for the printer's serial and 
parallel ports to be compatible with the user's host computer and driver 
installation.  This topic is divided into three main parts:  Macintosh, PC, and 
workstation.

Connecting the printer to a Macintosh

A direct connection between the printer and a Macintosh would be through the 
printer's LocalTalk port.  A networked connection for a Macintosh will most 
likely be either a LocalTalk network or an Ethernet network.  

LocalTalk connection to a Macintosh

1.

Turn off the printer.  LocalTalk protocol requires that you attach the 
LocalTalk cable with the printer powered off.  

2.

For a direct connection, attach the interface cable or adapter to the host 
computer's LocalTalk port.  (The port has a printer icon printed next to 
it.)  Attach the other end to the printer’s LocalTalk port.

For a LocalTalk network connection, attach the network adapter to the 
printer's LocalTalk port.

3.

Turn on the printer and the computer.

Ethernet connection to a Macintosh

Note

For an Ethernet connection, the printer must have the Ethernet option 
card installed.  An Ethernet “Installed” label will be attached to the 
rear panel next to the Ethernet connector.

1.

Turn off the printer.  Ethernet protocol requires that you attach the 
Ethernet cable with the printer powered off.  

2.

Attach the Ethernet network adapter to the printer's Ethernet 
connector.  

3.

Turn on the printer.  During the printer's boot-up process, the printer's 
network name or node address is resolved with the network and is 
displayed in the Mac's Chooser.

Summary of Contents for Phaser 440
































































































































































































































Reviews:

No comments

Related manuals for Phaser 440

olympia electronics A-200 Manual preview
A-200
Brand: olympia electronics Pages: 4
Xante Accel-a-Writer 8300 Maintenance And Specifications preview
Accel-a-Writer 8300
Brand: Xante Pages: 12
Xerox 3635MFP - Phaser B/W Laser Evaluator Manual preview
3635MFP - Phaser B/W Laser
Brand: Xerox Pages: 16
Xerox WorkCentre 7525 User Manual preview
WorkCentre 7525
Brand: Xerox Pages: 70
Xerox WorkCentre 7525 Quick Manual preview
WorkCentre 7525
Brand: Xerox Pages: 8
Xerox WorkCentre 7328 Quick Network Setup Manual preview
WorkCentre 7328
Brand: Xerox Pages: 24
Xerox WorkCentre 7232 Copying Manual preview
WorkCentre 7232
Brand: Xerox Pages: 4
Xerox WorkCentre 7232 Evaluator Manual preview
WorkCentre 7232
Brand: Xerox Pages: 24
Xerox WorkCentre 7232 System Administrator Manual preview
WorkCentre 7232
Brand: Xerox Pages: 236
Xerox WorkCentre 7232 Quick Use Manual preview
WorkCentre 7232
Brand: Xerox Pages: 128
Xerox WorkCentre 7232 Quick Network Setup Manual preview
WorkCentre 7232
Brand: Xerox Pages: 25
Xerox WorkCentre 7232 Voluntary Product Accessibility Template preview
WorkCentre 7232
Brand: Xerox Pages: 8
Xerox WorkCentre 7228 Quick Manual preview
WorkCentre 7228
Brand: Xerox Pages: 22
Xerox WorkCentre 7228 System Administrator Manual preview
WorkCentre 7228
Brand: Xerox Pages: 300
Xerox WorkCentre 7300 Series Quick Use Manual preview
WorkCentre 7300 Series
Brand: Xerox Pages: 128
Xerox WorkCentre 7132 Service Manual preview
WorkCentre 7132
Brand: Xerox Pages: 27
Xerox WorkCentre 7300 Series Troubleshooting Manual preview
WorkCentre 7300 Series
Brand: Xerox Pages: 40
Xerox 6200DX - Phaser Color Laser Printer Troubleshooting Manual preview
6200DX - Phaser Color Laser Printer
Brand: Xerox Pages: 42

Brands by name

Popular brands

Load more brands