Installation—MicroLab
|
Instruction
Other Considerations
Be
sure
to
observe
these
basic
safety precautions
with
the
power
cord:
©
Keep
the
power
cord
off
the
floor.
@
Dress the
power
cord
to
the rear
of
the
MicroLab
I.
@
Don’t
set other
equipment
on
top
of
the
power
cord.
Personality Card Installation
;
CAUTION
;
Each
personality card contains devices that
are
Static-sensitive.
In
order
to
prevent damage
to
a
static-sensitive
part,
handle the personality cards
only
in
a
static-free
environment.
Personality cards
must
be
stored
in
pink
polyethylene
bags,
or
laid
on
conductive work
surfaces
only.
See Section
7
of
this
manual
for
more
information on
handling static
sensitive parts.
The
personality card
is
always
mounted
so
that
the
zero-
insertion-force
(ZIF)
socket
is
facing upward,
as
shown
in
Fig.
4-1.
The
personality card slides
into
the
MicroLab
|
through
the
front
panel. The card
is
guided
along
two
rails
until
the
card’s
edge connector
fits snugly
into
the
MicroLab
|
edge
connector
socket.
To
mount
the
personality
card, perform
the
following
steps:
1.
Make
sure
that
primary
power
to
the
MicroLab
|
is
OFF.
2.
Swing
the
plastic
dust
cover
upward,
until
it
rests
in
the
vertical position.
3. At
this
point, make
sure that
any jumpers
on your
personality card
have
been
set
properly.
4. Slide
the personality
card
(ZIF
socket
up)
partway
into
the
guide
rails.
5.
Positioning your
hands as
shown
in
Fig.
4-1,
press the
personality
card
with
your
thumbs
until
the
card
is
seated.
6.
Make
sure
that
the
ZIF
socket
lever
is
inthe downward
position;
then
close
the dust
cover.
The cover
will
snap
into place.
To
remove
a
personality
card, perform
the
following steps:
1.
Make
sure
that
primary
power
to
the
MicroLab
|
is
OFF.
2.
Swing
the plastic
dust
cover upward,
until
it
rests
in
the
vertical position.
4-2
3.
Grasping
the two white
ejector levers,
pull
the levers
until
the
personality card
comes
free
of
the
MicroLab
|.
4.
After removing the personality
card,
place
the
card
into
the spare
slot
in
the
MicroLab
|,
or
on
a
conductive
surface
such
as
pink
polyethylene
or conductive foam
2827-10
Fig.
4-1.
Installing
A
Personality Card.
The
personality card
is
always
installed
with
the
ZIF
socket facing
upward. Push the
card
firmly
into
the
MicroLab
|
with both
thumbs.
Checking Out
The
MicroLab
|
Once you've unpacked
the
MicroLab|
and
installed
a
personality
card, refer back to Section
2 of
this
manual and
perform
the self-test
function described
there.
If
the
MicroLab
|
fails
any
of
the tests, contact
your
nearest
Tektronix Service Center.
After
performing
the
self-test
functions,
set the
MicroLab
|
baud
rates,
as
described
in
the
following
paragraphs.
Setting
The
MicroLab
|
Baud
Rate
The MicroLab
|
can
communicate
with
an
optional
terminal
through
an RS-232-C port located on
the
side
of
the
MicroLab! chassis. The
rate
at which
data
can be
transmitted
or received
is
selectable.
Open
the
plastic lidon
the
front
of
the
MicroLab
I,
and
notice
a
row
of square
pins,
as shown
in Fig.
4-2. These square
pins select the
transmit/receive
baud
rates
for
the
terminal RS-232-C
port
and
for
the modem RS-232-C
port.
The row
of
square
pins
labeled
J1080
select
the
baud
rate
for
the terminal
RS-232-C port (the upper connector
on
the
side
of
the
MicroLab
|).
The row
of
square
pins labeled
J1070
select the
baud
rate
for
the
modem RS-232-C port
(the lower
connector
on
the
side
of
the
MicroLab
|).
Summary of Contents for 067-0892-00
