background image

9.  Use  your  turn  signals,  checking  for  traffic  well  in  advance  of  turning

If  the  mower  is  not 

equipped  with  turn  signals  and  law  requires  them,  install  them  prior  to  operating  on  or  near 
public roads. 
 
 

Safety Decals 
 

1. Keep decals clean. Remove dirt with a wet clean cloth when necessary. 
2. Replace safety decals if destroyed, missing, painted over or unreadable. If any safety decals 
are  covered  or  obscured  when  the  ROPS  is  mounted,  it  is  recommended  that  you  purchase 
replacement decals  from  the  mower  manufacturer.  Mount them  in  a readable  location  at,  or 
near, their original location before operating the mower. 
3. New ROPS decals and mower decals are available from your mower dealer. 
 
 

ROPS Safety 
 

1. Install the ROPS in accordance with Tektite mounting instructions. Failure to do so may affect 
the ROPS ability to withstand a roll over.  
2. If the ROPS is subjected to alteration, structural damage or involved in an over turn accident, 
the entire structure must be replaced. Failure to do so may result in injury or death in the event 
of a roll over. 
3. If the mower in not equipped with seat belts, purchase approved seat belts from the mower 
manufacturer or Tektite prior to operating the mower. 
4. Always fasten seat belts prior to operating the mower. 
5. Always operate the mower from the 

operator’s seat.

 

6. Remove mud, crop residue, chains and 

tools from steps and operator’s

 platform. They may 

interfere with pedal operation or entry/exit from the mower. 
7. Remove all loose chains, tools, and equipment from the 

operator’s platform

. Failure to do so 

may cause injury or death in the event of a roll over. 
8. Do not install the ROPS on a mower model that the ROPS is not designated for (compatible 
mower  designations  are  printed  on  the  ROPS  serial  number  plate).    The  ROPS  is  designed 
specifically for individual models to ensure ROPS requirements will be met. Installing the ROPS 
on a non designated mower may result in injury or death. 
 
 

Emergency Exits 
 

This ROPS cab has 2 exits, which may be used in an emergency: left and right doors. 
 
 

 

    June 2021© New Holland G6035 Series ROPS Cab Operation Manual

Summary of Contents for New Holland 6035











































Reviews: