manualshive.com logo in svg

TECOM CHALLENGER, User Manual

Share
Download
TECOM CHALLENGER User Manual Download Page 50

50

V8-U-TXT.PM6 :    Issue I , Revision I : October 1997

PROGRAM  USERS 

 -  Menu Option 14

8.

The display will show.

Your Name is , (*)-End

This allows you to enter a user’s name of up to 16 characters, by using the text option on the keypad.
Keys 1 to 9 have alphabetical characters printed above them.  To enter a letter, press the key the number of times
relative to the position of the letter.  Both upper and lower case letters are available as well as the numerical values.
Refer to Figure 2.

After entering a letter in the name, press 

ENTER

 to move the cursor to the next position.

?   ?   ENTER

~

Enter each letter of the user’s name followed by 

ENTER

.

or

ENTER

~

To move the cursor to the position after the name.

or

MENU *

~

Save the name. (And display the new name if programmed/changed)
If the name has been changed, only letters preceding the cursor will be saved.

and

MENU *

~

If name is programmed/changed. Save the name and move to the PIN code display.

CAUTION

When programming name text, the "ENTER" key is ONLY used to move the cursor.

Make sure that the procedure above is followed carefully when programming name text.

9.

The display will show.

eg.

Pin Code:
Code:

 

?   ?   ?   ?

~

Enter the PIN for this user.

See Notes 3, 4, 5 & 6.

ENTER

~

Save and display the PIN code.

ENTER

~

Return to the display shown in step 1.

Notes:

1.

You cannot create a user unless your alarm group authorizes you to do so.

2.

You cannot assign an alarm group to a user unless the alarm group has the option 

"Can this Alarm Group

be Assigned to Users" 

set to YES and 

your

 alarm group has all the 

"Areas"

 & 

"User Menu Options"

of the alarm group you wish to assign.  If the alarm group you wish to assign has 

"Alarm System Control"

&

"Modem Access"

 set to YES, then 

your

 alarm group must have these features set to YES also.

3.

You cannot program a PIN or User number that already exists.

4.

You cannot program a PIN that will conflict with another user's duress code.
(Refer to the section on Duress).

5.

You cannot program a PIN that will conflict with another user's door code.
(Refer to the section on Opening a Door).

6.

A User who will be allowed to both open doors and arm/disarm the system, should have a PIN of at
least 5 digits.  (Refer to the section on Opening a Door).

www.msealarms.com.au

Summary of Contents for CHALLENGER







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands