manualshive.com logo in svg

TECOM CHALLENGER, User Manual

Share
Download
TECOM CHALLENGER User Manual Download Page 13

13

The  Challenger

 Version 8.0 User Guide :    Issue I , Revision I : October  1997

The arming procedure is used (when leaving the premises) to set devices in your system to cause an alarm should there
be a change in their condition.  You are turning on the security for an area or building which is unoccupied.

-

The arming procedure will vary depending on how your system is programmed.
The recommended OFF/ON procedure is described in this User Guide.

-

Each arming station controls specific area/s.
Only the area/s controlled by an arming station can be armed at that arming station.

-

Each PIN will only be authorized to arm specific area/s.
When an arming procedure is used, only the area/s assigned to the PIN will be armed.

-

It is not possible to arm an area with an unsealed input.
If at any time during the arming process the console sounds 7 quick beeps and displays the word 

unsealed,

refer to the section on Unsealed Inputs.

-

After an area is armed you will have a pre-set time to exit the area before an alarm occurs.

ARMING YOUR SYSTEM

www.msealarms.com.au

Summary of Contents for CHALLENGER







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands