TECOM AR1061 User Manual Download Page 5

Page: 5 / 59

AR1061 1-port Ethernet ADSL2+ Router User‘s Manual

Page 5 of 59

2.2 Specifications

ADSL Standard

ITU-T G.992.1(G.dmt)

ANSI T1.413 Issue 2

G.992.2 (G.lite)

G.994.1 (G.hs)

Auto-negotiating rate adaptation

ADSL2 G.dmt.bis (G.992.3)

ADSL2 G.lite.bis (G.992.4)

ADSL2+ (G.992.5)

Software Features

RFC-1483/2684 LLC/VC-Mux bridged/routed mode

RFC-1577 Classical IP over ATM

RFC-2516 PPPoE

RFC-2364 PPPoA

ITU-T 1.610 F4/F5 OAM send and receive loop-back

802.1d Spanning-Tree Protocol

DHCP Client/Server/Relay

NAT

RIP v1/v2

DNS Relay Agent

DMZ support

IGMP Proxy/Snooping

Packet Inspection

Protection against Denial of Service attacks

IP Packet Filtering

QoS

Dynamic DNS

Management

Web-based Configuration

Menu-driven Command-line Interpreter

Telnet Remote Management

SNMP v1/v2/Trap

Firmware upgrade through FTP, TFTP and HTTP

Configuration backup/restore

Diagnostic Tool

Summary of Contents for AR1061



























































Search results

Summary of Contents for AR1061

Reviews:

Brands by name

Popular brands

TECOM AR1061, User Manual

Search results

Summary of Contents for AR1061

Reviews:

Brands by name

Popular brands