manualshive.com logo in svg

TECOM AR1061, User Manual

Share
Download
TECOM AR1061 User Manual Download Page 27

AR1061 1-port Ethernet ADSL2+ Router User‘s Manual   

 

 

 

Page 27 of 59 

 

 

Fields in this page: 

Field 

Description 

Enable DMZ 

Check this item to enable the DMZ feature. 

 

DMZ Host IP Address 

IP address of the local host. This feature sets a local host to be exposed to the 

Internet. 

 

Function buttons in this page: 

Apply Changes 

Click to save the setting to the configuration. 

IGMP Proxy Configuration 

Multicasting  is  useful  when  the  same  data  needs  to  be  sent  to  more  than  one  hosts. 

Using  multicasting  as  opposed  to  sending  the  same  data  to  the  individual  hosts  uses 

less  network  bandwidth.  The  multicast  feature  also  enables  you  to  receive  multicast 

video stream from multicast servers. 

IP hosts use Internet Group Management Protocol (IGMP) to report their multicast group 

memberships to neighboring routers. Similarly, multicast routers use IGMP to discover 

which  of  their  hosts belong  to multicast  groups. This  device  supports  IGMP  proxy  that 

handles  IGMP  messages.  When  enabled,  this  device  acts  as  a  proxy  for  a  LAN  host 

Summary of Contents for AR1061




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands