manualshive.com logo in svg

TECOM AR1061, User Manual

Share
Download
TECOM AR1061 User Manual Download Page 40

AR1061 1-port Ethernet ADSL2+ Router User‘s Manual   

 

 

 

Page 40 of 59 

 

Fields in this page: 

Field 

Description 

Select the Internet 

Connection 

The available WAN side interfaces are listed. You have to select one for the WAN 

side diagnostic. 

 

 

 

4.8  Admin 

Commit / Reboot 

Whenever you use the Web configuration to change system settings, the changes are 

initially placed in temporary storage. These changes will be lost if the device is reset or 

turn off. To save your change for future use, you can use the commit function. 

 

 

 

Function buttons in this page: 

Commit and Reboot 

Whenever you use the web console to change system settings, the changes are 

initially placed in temporary storage. To save your changes for future use, you can 

use the Commit/Reboot function. This function saves your changes from RAM to 

flash memory and reboot the system. 

 

IMPORTANT!

   

Do not turn off your modem or press the Reset button while this procedure is in progress. 

Summary of Contents for AR1061




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands