background image

ENGLISH 

UPS EVO DSP PLUS 1.2-2.4-3.6 MM 

1

 

User’s manual 

 

User’s Manual - English 

 
 

Safety Warnings 

 

                                                                     

 

 

Read  this  manual  carefully  and  completely  before  installing  and  using  the  EVO  DSP  PLUS  MM 
Uninterruptible Power Supply, which, from here after, will also be referred to as UPS. 

 

The  UPS  must  be  used  only  by  properly  trained  personnel.  To  ensure  correct  and  safe 
operations,  it  is  necessary  that  operators  and  maintenance  personnel  observe  the  general 
safety Standards as well as the specific instructions included in this manual. 

 

Risk of electric shock: do not remove the cover. The UPS contains internal parts which are at a 
high  Voltage  and  are  potentially  dangerous,  capable  of  causing  injury  or  death  by  electric 
shock. 

 

There  are no internal parts in the UPS which are user serviceable. Any repair or maintenance 
work  must  be  performed  exclusively  by  qualified  technical  personnel  authorized  by  producer. 
TECNOWARE declines any responsibility if this warning is disregarded.  

 

The electric installation has to be done by qualified personnel. Follow all the Safety Standards 
(CEI  Standards  in  Italy  or  IEEE  elsewhere)  for  the  Input/Output  connections  and  for  the  right 
section of Input/Output cables.  

 

It is compulsory to ground the UPS according to Safety Standards. 

 

Risk of electric shock at the Output lines when the UPS is ON. 

 

Risk of electric shock at the Output lines while the unit is connected to the AC utility line. 

 

For  respect  of  the  Safety  Standards  is  necessary  the  presence  of a differential circuit breaker 
between UPS Output lines and the loads. 

 

We recommend to use a dedicate AC power line for the UPS. 

 

Do not obstruct ventilation slots or holes and do not rest any object on top of the UPS. 

 

Do not insert objects or pour liquids in the ventilation holes. 

 

Install the UPS indoors, in a protected, clean and moisture-free environment. 

 

Do not expose to the direct sun light. 

 

Do not keep liquids, flammable gases or corrosive substances near the UPS.  

                                                                     

 

 

 

Summary of Contents for EVO DSP PLUS MM 1.2



























Reviews: