background image

ENGLISH 

User’s manual 

10

 

UPS EVO DSP PLUS 1.2-2.4-3.6 MM 

 
 

Graphic LCD Panel 

Function  

Battery information 

 

Indicates the Battery capacity by 0-25%, 26-50%, 51-75%, and 76-100%. 

 

Indicates the Battery is faulty or defective. 

 

Indicates Low Battery level and Low Battery Voltage. 

Input and Battery Voltage information 

 

Indicates the Input Voltage or Frequency or Battery Voltage. 
Vac: Input Voltage, Vdc: Battery Voltage, Hz: Input Frequency 

 

5.1.2  Buttons 

Functions of the buttons are given below: 

Button 

Function 

ON/MUTE 

Turn ON the UPS

: press and hold ON/MUTE button for at least 3 seconds to turn ON the UPS. 

Mute  the  acoustic  alarm: 

when  the  UPS  is  in  Battery  mode,  press  and  hold  this  button  for  at 

least  5  seconds  to  disable  or  enable  the  acoustic  alarm.  But  it’s  not  applied  to  the  situations 
when warnings or errors occur.

  

Test Battery

: press and hold ON/MUTE button for at least 5 seconds to perform the Battery Test 

while the UPS is in Normal mode. 

SELECT 

Select the measurements on the graphic display

: by pressing the SELECT button it is possible 

to  choose  the  electrical  parameter  to  be  displayed  (Input  Voltage,  Input  Frequency,  Battery 
Voltage,  Output  Voltage,  Output  Frequency).  If  the  button  is  not  pressed  for  at  least  10 
seconds,  then  the  default  parameter  will  came  back  on  the  graphic  display  (the  default 
parameters are Input Voltage and Output Voltage). 

OFF/ENTER 

Turn OFF the UPS

: press and hold ON/MUTE button for at least 3 seconds to turn OFF the UPS. 

By pressing this button while the UPS is in Normal mode, the UPS will go to Stand-by mode; by 
pressing this button while the UPS is in Battery mode, the UPS will switch OFF completely. 

ON/MUTE      

SELECT 

Switch  to  Bypass  mode

:  when  the  UPS  is  functioning  in  Normal  Mode,  press  ON/MUTE  and 

SELECT buttons simultaneously for at least 5 seconds. Then UPS will enter to Bypass mode. This 
action will be ineffective when the Input voltage is out of the acceptable range. 

 

Summary of Contents for EVO DSP PLUS MM 1.2



























Reviews: