Tecno Automazione T011S User Manual Download Page 17

Page: 17 / 20

PROGRAMMING OBSTACLE SENSOR

OBSTACLE

PROGRAMMING

helps you to program the obstacle detection sensor.

sets:

•

→

Motor A

standard obstacle detection threshold

•

→

Motor A

slowdown obstacle detection threshold

HOW-TO:

The gate must be closed.

Selecting

using buttons A/B.

When display shows

press a START command.

The display shows

motor closing pushing on the mechanical stop. The control board has

detected the maximum motor stress when an obstacle is in the path of the gate.

The display shows

motor A opens for 4 seconds. motor stops. The control board has detected

the motors stress without any obstacle.

The display sho

the gate returns to initial position. When motor stops the procedure is

finished.

If the display shows

an error has occurred during the procedure.

Any command during the steps 2,3,4,5,6 stops

programming and display will show

After programming you can modify the obstacle parameters manually. For instance you can disable

slowdown obstacle detection

setting

www.tecnoautomazione.com

Pag. 15 / 17

Summary of Contents for T011S





















Search results

Summary of Contents for T011S

Reviews:

Related manuals for T011S

Brands by name

Popular brands

Tecno Automazione T011S, User Manual

Search results

Summary of Contents for T011S

Reviews:

Related manuals for T011S

Brands by name

Popular brands