background image

VRD-485 RFID READER WITH RS-485 INTERFACE 

Revision number: 1.01  

Review date: 1 December, 2021

 

www.technotrade.ua

 

 

page 4 from 13 

 

PURPOSE OF THE DOCUMENT 

 

This  Technical  Guide  is  intended  for  studying  of  VRD-485  RFID  reader  with  RS-485  interface.  It  contains 
basic information regarding its technical characteristics, connection scheme and configuration. 

 

 

Due to a reason that VRD-485 RFID reader with RS-485 interface is constantly being developed in direction 
of  improvements  of  their  possibilities,  changes  are  possible  in  its  final  version,  which  is  not  described  in 
given Technical Guide. 

 

During the system development process given Technical Guide will be also expanded and updated and new 
chapters will be added. Latest version of this Technical Guide can be downloaded from the VRD-485 RFID 
reader with RS-485 interface web-page

https://www.technotrade.ua/vrd-e-card-reader.html

. 

 

Due to a reason that VRD-485 RFID firmware is constantly being developed in direction of improvement of 
its possibilities, changes are possible in final version, which are not described in given Technical Guide. 

 

During  the  system  development  process  given  Technical  Guide  is  also  expanded  and  updated  and  new 
chapters are added. Latest version of this Technical Guide can be downloaded from the VRD-485 RFID web-
page: 

https://www.technotrade.ua/vrd-485-reader.html

. 

 

Technotrade  LLC  hereby  permits  reproduction  of  this  document  as  may  be  required  by  any  of  the 
customers or OEMs wishing to use it. 

 

This document has been carefully prepared and is believed to be accurate. However, Technotrade LLC, its 
employees and its agents do not assume responsibility for its use either directly or indirectly. Technotrade 
LLC  shall  not  be  liable  for  technical  or  editorial  errors  or  omissions  which  may  appear  in  this  document. 
Technotrade LLC reserves a right to make changes to this document at any time without notice. Prospective 
users  of  this  document  should  contact  Technotrade  LLC  at  the  time  they  wish  to  use  VRD  RFID  reader 
together with their products to become aware of any updates that may apply.  

 

In case if you find any mistakes, omissions in this document or have any suggestions on improvements to 
this  document,  please feel free to e-mail them to our support mailbox: 

[email protected]

We 

will be grateful to you for this valuable information. 

 

All technical questions regarding the  VRD-485  RFID  reader  are welcome to be asked on support mailbox: 

[email protected]

. Our support team will be glad to help you. 

 

Also, you can call to us or visit us on:  

Technotrade LLC

 

Ukraine, 04114 Kiev, Priorska str. 10, office 1 
Tel: +38-044-502-46-55, +38-044-502-46-77 
Web

www.technotrade.ua

 

Mail

[email protected]

 

 
 
 

 
 

 

 

Summary of Contents for VRD-485














Reviews: