background image

VRD-485 RFID READER WITH RS-485 INTERFACE 

Revision number: 1.01  

Review date: 1 December, 2021

 

www.technotrade.ua

 

 

page 11 from 13 

 

Command 06 

‘Write Single Register’ 

 
This command is recommended for setting the reader address and baud rate. 
 
Request: 

Request code 

1 byte 

0x06 

Register number 

2 bytes 

0x0000 

… 0x000B

 

Value (for example address 
(High) and baud rate (Low)) 

2 bytes 

0xXXXX 

 
Response: 

Response code 

1 byte 

0x06 

Register number 

2 bytes 

0x0000 

… 0x000B

 

Value (for example address 
(High) and baud rate (Low)) 

2 bytes 

0xXXXX 

 
Example: 

REQUEST 

RESPONSE 

Request code 

0x06 

Response code 

0x06 

Register High number  

0x00 

Register High number 

 

0x00 

Register Low number 

0x00 

Register Low number

 

0x00 

Reader address 27 

0x1B 

Reader address 27

 

0x1B 

Baud rate 9600 

0x02 

Baud rate 9600

 

0x02 

 
In this example address of the reader is set to 27 and its baud rate is set to 9600. 
 

Note! 

If the baud rate value is not within the range 1 

 6 

 then the least possible baud rate is set (2400). 

 
Response in case of the request error: 

Response code 

1 byte 

0x86 

Error code 

1 byte 

0x02 

 start register number is more than 0x000B 

 

Summary of Contents for VRD-485














Reviews: