background image

TECHNOTHERM

7

For installations under difficult condi-

tions, these mounting accessories are 

available:

Mountik kit RDX

The instant water heater can be instal-

led by means of this mounting kit in 

the below situations. The power supply 

cable is coming out of the wall at any 

place from behind the unit, but the 

wall has unusual surface conditions, 

making it difficult for installing the 

water heater. The power supply cable is 

coming from elsewhere and has to be 

connected to the back of the unit.

Mounting accessories

Extension kit VDX

RDX is necessary!

The instant water heater can be instal-

led by means of this extension kit if the 

water pipes are coming displaced or 

exchanged out of the wall or if they are 

coming edge-wise on the wall to the 

unit. The power supply could come out 

of the wall at any place under the unit 

or the wiring could be installed 

 

surface-mounted.

Extension kit UDX 

 RDX is necessary!

The instant water heater can be instal-

led by means of this extension kit if the 

water-connections are expiring above 

the unit. The power supply could come 

out of the wall at any place under the 

unit or the wiring could be installed 

surface-mounted.

5. Installation

Summary of Contents for CDE 18-27 VarioSelect





















Reviews: