Technotherm CDE 18-27 VarioSelect Installation And Technical Manual Download

Page: 18 / 20

VarioSelectCDE 18-27 TECHNOTHERM

Problem

Cause

Solution

Water stays cold, display does

not light up

Master fuse tripped

Renew or activate fuse

Safety pressure cut-out

tripped

Contact customer service

Water stays cold, display does

light up

Safety thermal cut-out

tripped

Contact customer service

Flow rate of hot water too

weak

Outlet fitting dirty or

calcified

Clean shower head, jet

regulator or sieves

Fine filter dirty or

calcified

Clean fine filter

Selected temperature is not

reached

Excessive water flow

(winter?)

Reduce water flow rate at

the outlet

Elected power too small

Control the set power:

1. Check power selector

plug

2.Carry out a reset, note

blink code

Selected temperature is

perceived as too cold

Set temperature too low Increase set temperature by

keypress

Selected temperature is

perceived as too hot

Set temperature too high Decrease set temperature

by keypress

Lucht LHZ Elektroheizung GmbH
Obere Hauptstr. 61

09232 Hartmannsdorf
Germany
Telefon: +49 (0) 3722 63370

Telefax: +49 (0) 3722 633720

E-Mail: [email protected]

13. Self-help and customer service

Repairs must only be carried

out by authorised professio-

nals.

If a fault in your appliance

cannot be rectified with the

aid of this table, please con-

tact the service organisa tion

of your importer or the Cen-

tral Customer Service Depart-

ment. Please have the details

of the typeplate at hand!

Summary of Contents for CDE 18-27 VarioSelect





















Search results

Summary of Contents for CDE 18-27 VarioSelect

Reviews:

Related manuals for CDE 18-27 VarioSelect

Brands by name

Popular brands

Technotherm CDE 18-27 VarioSelect, Installation And Technical Manual

Search results

Summary of Contents for CDE 18-27 VarioSelect

Reviews:

Related manuals for CDE 18-27 VarioSelect

Brands by name

Popular brands