background image

10

GB

4.1

CONNECTING THE CONDENSATE DISCHARGE PIPE

   (For air handlers which can operate in cooling mode)

• Connect the condensate pipe to a discharge pipe.

• Fix the two pipes using adhesive tape:

- MW 2, MW 3: Ø 18 mm.
- MW 4, MW 5: Ø 26 mm.

• For air handlers equipped with a condensate lift system, the pump discharge is

connected to a flexible PVC pipe of internal diameter 6 mm, equipped with a splined
connector.
See the "Technical Manual" for the pressures available at the discharge.

4 - CONNECTIONS

C o n d e n s a t e
d i s c h a r g e

Adhesive
t a p e

4.2

HYDRAULIC CONNECTION

• MW can be connected either with metric copper pipe or with PER

(interlaced polyethylene).

• Diameter of the pipes to be used:

- MW 2 and MW 3:

- copper pipe 10/12 or
- PER pipe 10/12

- MW 4 and MW 5:

- copper pipe 14/16 or
- PER pipe 13/16

• Adaptors for copper pipe or PER pipe are supplied with the air handler.

Trap

Condensate discharge
p i p e

Immersion

Slope

IMPORTANT NOTE

• If the end of the condensate discharge pipe goes into the

water and forms a trap, the flow will not be correct and the
condensate will flow in the internal unit (see drawing
opposite).

• Check that the condensate is discharged smoothly.

• Seal the hole in the wall through which the pipes pass in

order to prevent water entering.

• Using a bottle, pour water into the condensate tray in order

to ensure that the water is correctly discharged.

4.2.1  ORIENTATION OF THE PIPES

2

Copper pipe

P.E.R. pipe

• For orientations   1   cut the plate (in

order to put the pipes through leaving
the contour free from any roughness).

• Keep the piece of plate cut for possi-

ble later use.

1

Cover

S e a l i n g
c o m p o u n d

Summary of Contents for MW 2

















Reviews: