I
UK
D
E
F
NL
P
S
DK
FIN
B
GR
CZ
EE
LV
LT
H
M
PL
SK
SLO
7
Operator's guide
9. CONNECTION TO MAINS
1
4
5
10. CONTROLS
1 Rotation switch:
2 Light switch:
3. Refrigeration switch:
4. Termometer:
5
“
SET
”
6
“
UP
”
7
“
DOWN
”
MAKE SURE THAT: 1
12. INTERNAL CLEANING (EVERY 15 DAYS)
1
2
3
13. REPLACEMENT OF INTERNALIGHT
1
2
3
4
5
(NO LED) 6
7
14. REPLACEMENT OF THE DOOR MAGNETIC GASKET
1
2.
3
.
.
.
The controls of the appliance are situated at the front inside a protected recess. .
to
run the rotating shelves. The rotation stops immediately when opening the door or if encountering even a
slight obstruction. .
to switch on the light inside the appliance.
to run the refrigeration system.
to read the temperature in the appliance.
o adjust the temperature: pushing once the button
the display will show the temperature of the cell, pushing several times the button
the
temperature increases while pushing several times the button
the temperature decreases
. T
.
.Switch off electricity supply. . Open the door and remove the dislpayed foodstuffs. . Wipe the internal
surfaces and the accessories of the appliance with a sponge dipped in water with a little bicarbonate of
soda.Dry with care.
. Switch off electricity supply. . Unscrew the screws fixing the upper light holder. . Detach the
fluorescent tube from the upper lamp holder. . Remove the tube from the lower lamp holder. . Remove
the transparent protective tube
. . Replace the fluorescent tube. . Replace everything in
reverse order
.Open the door.
Take hold of the magnetic gasket with your hands and remove it from the frame.
. Insert the new gasket and press all around it when in place
Ensure that mains voltage and frequency are the same as those stated on the rating plate ( )
attached to the appliance.
Ensure that the supply socket has the following characteristics:
-
-
. Ensure that there is no danger of explosion (AD)
in the room.
The connecting cable to the appliance is H05 VVF, designed for internal use only. For
different setting it is necessary to change it (for example H07 VVF for external settings)
in case
the appliance, during the trasport or storage, has been erroneously placed in horizontal position or
upside-down, it must be left in the correct position for at least 3 hours before connecting it to the
electrical supply.
Insert the plug (do not use triple and reduction outlets) (see picture 8).
to
adjust the temperature inside the appliance. In order t
(see picture 9).
he plug is connected
. Refrigeration unit switch is on(green light lit up). . The
thermometer shows the desired temperature for the foodstuffs to be stored in. . Internal light and
rotation switches are on. . The door is closed. . The appliance is not exposed to the direct light of the
sun or to high powered lamps. . The room temperature does not exceed that in which the appliance is
designed to work normally, i.e. +30° C 55% r.h. . The compressor ventilation grilles are free from
obstruction for at least 30 cm.
The foodstuffs are placed on the shelves in the right way, in order to
ensure a good circulation of the cool air, especially between the rear glass panel and the shelves,
where the air outlets are.
(see picture 10).
(see picture 11).
A
2.
3
Notice:
Thermostat:
11. CHECKING THE CORRECT FUNCTIONING
2
3
4
5
6
7
8
9.
a)
b)
c)
It is
properly earthed.
It is appropriate for the nominal current as set out on the rating plate.
It complies
with the IEC regulations: Magneto-thermic differential switch with In = nominal value as stated on the
rating plate; Differential with Id sensitivity = 30 mA.
