> no interference of the roadworthiness,
> good access of the controls of the car ,
> sufficient air circulation to prevent overheating of the radio in transmit mode.
Please take into account that the LC display ( 6 ) is only good readable from a certain angle.
An intensive solar irradiation can also affect the readability of the display. So it is recommen-
ded to check the best position before the final inst allation. The unit can easily be fixed onto
different positions in the car by using the enclosed mounting bracket.
4) Microphone DM-106S
Plug the microphone ( 1 ) into the 6 pin socket ( 12 ) on the front panel. Note it will only go in
one way round. No transmission and receiving is possible without the microphone. The pin
assignment of the GDCH standard microphone plug is given below:
PIN 1 Modulation
PIN 2 Loudspeaker
PIN 3 PTT
PIN 4 Up/Down
PIN 5 Ground
PIN 6 +12 Volt
Solder side view of the microphone connector or top view of the microphone plug.
The standard microphone DM-106S, which is equipped with channel selection and signal
tone, is included with the MX8 Mark-I. This microphone is the best selection for the MX8
Mark-I.
5) Power source
Before connecting the unit to a suitable power source via the fused DC power cable (16), the
device must be switched off by turning the volume control ( 11 ) [
Vol / Off
] anticlockwise as
far as the stop and hearing a switching sound.
Then, connect the two naked leads at the end of the cable with the supply volt
age of the
car/lorry battery. The unit is designed to operate with 12 volt s and a negative ground electri-
cal system. Lay the cable as far as possible away from aggregates which can cause interfe-
rence. Watch for the correct polarity during the connection.
BLACK connect to - MINUS / ground of the car battery .
RED
connect to 12 volts + PLUS of the car/lorry battery.
If the power source is not disconnected af ter putting the engine of f, the last settings will
remain stored, after the unit and the car are switched of f.
For base-station operation use a suit able power supply (13.2 V / 2.5 A, e. g. TEAM LabNT
series). The power supply should be designed for operation with a transceiver
, otherwise
interference from the mains or over-voltage may occur.
After proper connection of the microphone, the aerial and power source, radio operation can
be started.
Operation of the TEAM MX8 Mark-I
1) Switching on [ Vol / Off ]
Before switching the unit set the squelch control ( 10 ) [
SQ / Asq
] to the counterclockwise stop
but without activating the internal switch. The device is switched on by turning the volume con-
trol ( 11 ) [
Vol / Off
] clockwise to the centre position. The symbols are shown at the LC display
( 6 ) and the LCD backlight is illuminated. When being switched on after a disruption of the sup-
ply source the unit works on channel number 9 in FM mode and the LCD back-light is illuminat-
ed in orange or blue. Adjust the receiver sound with the volume control to the desired level.
All settings, which are made during operation of the transceiver , remain memorized after the
unit is switched off, as long as the power supply is not disrupted.
2
) Squelch [ SQ / Asq ]
The strong background noise, which occurs always on free channels, can be suppressed by
the squelch function. By turning the squelch control ( 10 ) [
SQ / Asq
] slowly clockwise you
will find a point where the noise disappears. The squelch control should only be turned up far
enough to stop the background noise on an unused channel. Turning the control further clock-
wise will increasingly suppress stronger interfering signals as well as weak st ations.
The automatic squelch [
Asq
] can be activated by turning the squelch control counterclock-
wise until the control clicks. In this position the normal squelch function is switched of f and
the squelch threshold is set to default.
3) Channel selection
[
] [
]
All channels can be selected by pushing the channel selector keys ( 2 ) [
] and ( 3 ) [
]
at the microphone, or by turning the rotary channel selector ( 9 ) [
Channel
] on the front panel
to the desired channel. The channel will be displayed on the LCD ( 6 ) with big digits and the
frequency with small digit s. No channel selection is possible while the radio is in TX mode.
The channels step in a ring like system. That means you go from the highest channel num-
ber to channel 1 and vice versa. For communication with a p artner CB st ation, both trans-
ceivers must be adjusted to the same channel and the same modulation type.
4) Receipt Tone selection Hi / Lo
[
Mode
]
The receipt tone selection is only available with the radio version MX8 Mark-I c (EC CEPT)
and the norm EC with the version MX8 Mark-I Multi Norm.
To toogle between the receipt tone high and low , press the receipt tone key ( 7 ) [
Mode
].
When being switched on after a disruption of the supply source the receiving sound is set to
low, which is indicated in the LCD by the symbol "
LO
". By pushing the receipt tone key
( 7 ) [
Mode
] the receiving tone is changing to a bright sound in the loudspeaker. This is indi-
cated in the LCD window by the symbol "
HI
".
5) LCD background illumination [ B ]
By pressing briefly the LCD illumination toggle key ( 16 ) [
B
], the LCD backlight illumination
color switches between orange and blue.
To switch off the background color, press the LCD illumination toggle key ( 16 ) [
B
] for about
2-3 seconds.
To permanently store the selected background color, i.e. after turning the radio on the same
English
English
14
15
mx-8mark1_manual.qxp 14.09.2009 16:45 Seite 14
