background image

11

Steering Servo Installation/Removal

Unplug the servo lead from the receiver. Remove the four 

small screws located on the bottom of the chassis that 

secure the servo to the chassis. Use a screwdriver or small 

pliers to pop the steering link off of the servo, so it can be 

removed. Replace in the reverse sequence used to remove 

the servo.

Receiver/Speed Control (ESC)  

Installation/Removal

Unplug the power lead, motor leads and steering servo. Do 

not attempt to open the receiver or electronic speed control 

(ESC) as only a factory technician has the proper tools 

and parts to make any repairs necessary. The receiver and 

ESC are mounted with double-sided foam tape. Use your 

thumb and index finger at the bottom of the front corners 

to pull them from the mount. If this is difficult, ask for help. 

If necessary, carefully use a large flat blade screwdriver 

between the unit and the mount to pry it loose. Make 

sure you remove any left over foam or adhesive before 

remounting with common servo tape or hobby type foam 

tape.

Warranty and Repair Policy

wARRANty peRiOd

Exclusive Warranty- Horizon Hobby, Inc., (Horizon) 

warranties that the Products purchased (the “Product”) will 

be free from defects in materials and workmanship at the 

date of purchase by the Purchaser. 

liMited wARRANty

horizon reserves the right to change or modify this 

warranty without notice and disclaims all other 

warranties, express or implied.

(a) This warranty is limited to the original Purchaser 

(“Purchaser”) and is not transferable. REPAIR OR 

REPLACEMENT AS PROVIDED UNDER THIS WARRANTY 

IS THE EXCLUSIVE REMEDY OF THE PURCHASER. This 

warranty covers only those Products purchased from an 

authorized Horizon dealer. Third party transactions are not 

covered by this warranty. Proof of purchase is required for all 

warranty claims.

(b) Limitations- HORIZON MAKES NO WARRANTY OR 

REPRESENTATION, EXPRESS OR IMPLIED, ABOUT 

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS 

FOR A PARTICULAR PURPOSE OF THE PRODUCT. 

THE PURCHASER ACKNOWLEDGES THAT THEY 

ALONE HAVE DETERMINED THAT THE PRODUCT 

WILL SUITABLY MEET THE REQUIREMENTS OF THE 

PURCHASER’S INTENDED USE.

(c) Purchaser Remedy- Horizon’s sole obligation hereunder 

shall be that Horizon will, at its option, (i) repair or (ii) replace, 

any Product determined by Horizon to be defective. In 

the event of a defect, these are the Purchaser’s exclusive 

remedies. Horizon reserves the right to inspect any and 

all equipment involved in a warranty claim. Repair or 

replacement decisions are at the sole discretion of Horizon. 

This warranty does not cover cosmetic damage or damage 

due to acts of God, accident, misuse, abuse, negligence, 

commercial use, or modification of or to any part of the 

Product. This warranty does not cover damage due to 

improper installation, operation, maintenance, or attempted 

repair by anyone other than Horizon. Return of any Product 

by Purchaser must be approved in writing by Horizon before 

shipment.

dAMAge liMitS

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, 

INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF 

PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN 

ANY WAY CONNECTED WITH THE PRODUCT, WHETHER 

SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, 

NEGLIGENCE, OR STRICT LIABILITY. Further, in no event 

shall the liability of Horizon exceed the individual price of 

the Product on which liability is asserted. As Horizon has 

no control over use, setup, final assembly, modification 

or misuse, no liability shall be assumed nor accepted for 

any resulting damage or injury. By the act of use, setup or 

assembly, the user accepts all resulting liability.
If you as the Purchaser or user are not prepared to accept 

the liability associated with the use of this Product, you 

are advised to return this Product immediately in new and 

unused condition to the place of purchase.
Law: These Terms are governed by Illinois law (without 

regard to conflict of law principals).

Warranty Services

QueStiONS, ASSiStANce, ANd RepAiRS

Your local hobby store and/or place of purchase cannot 

provide warranty support or repair. Once assembly, setup 

or use of the Product has been started, you must contact 

Horizon directly. This will enable Horizon to better answer 

your questions and service you in the event that you may 

need any assistance. For questions or assistance, please 

direct your email to [email protected], or 

call 877.504.0233 toll free to speak to a Product Support 

representative. You may also find information on our website 

at www.horizonhobby.com.

Summary of Contents for mini SCT














Reviews: