TCS IMM2300 Product Information Download Page 7 | Manualshive

Page: 7 / 20

TCS IMM2300 Product Information Download Page 7

09/2011

7

TCS TürControlSysteme AG

Subject to technical modifications.

Mail: [email protected]

PI_IMM2300_Art0031160-uk.doc

Application

Manually controlled simplex communication can be activated.
The IMM 2300 is an indoor station for hands-free talking, manually controlled simplex

communication can be activated

It is designed for surface-mounting.
It is suitable for the operation in TCS video systems and combined audio/video systems.

Brief description

Basic module

  speech button: for call acceptance and switching over speaking / hearing
  light switch button
  blue door release button with floor door release function (can be activated)
  speech button: for call acceptance and reversing key speaking / hearing
  function key (ex works: with control function) with alternative allocation (can be acti-

vated): internal call, door release automatic, call diversion

  ring tones can be adjusted by the resident, choice of 13 ring tones
  acoustic call distinction between 2 doors, flat door and internal call
  ring tone volume can be adjusted manually, volume for internal communication adjusta-

ble

  ring tone mute with optical display
  optical display of door calls
  optical display of a busy line when communication is established
  automatic hands-free talking after internal call can be activated
  one parallel call can be activated
  sending of the sender serial number in case of internal calls can be (de-) activated,

source indication e.g. at IMM1100 or IMM2100 possible (with configuration software
configo

TM

)

unlimited communication time can be switched ON/OFF (with configuration software

configo

TM

)

(but limited by other indoor or front-door station, that is realising the voice communica-
tion)

audio privacy function and automatic call cut-OFF

Video module

video surveillance: image switch button to switch on the image resp. for switching be-

tween different cameras

  AS dependent video image activation
  4 control keys (right, left, up, down)
  brightness, color saturation / manually adjustable
  integrated two-wire video receiver for direct connection to TCS video systems

«
...
5
6
7
8
9
...
»

Summary of Contents for IMM2300





















Reviews:

No comments