manualshive.com logo in svg

Taylor C819, Operating Instructions Manual, Page: 23 / 49

Share
Download
Taylor C819 Operating Instructions Manual Download Page 23

19

Models C819 & C821

Operating Procedures

110603

Step 5

Press the MENU EDIT key.

Figure 28

Step 6

Press the STORE MENU TO USB key.

Figure 29

Step 7

Enter a file name (up to 8 characters) to save the
menu items, using the keyboard displayed on the
control. Press the OK key. The menu items are
saved to the USB flash drive.

Step 8

Remove the USB flash drive from the USB port and
reinstall the USB cable cap on the USB connector.

Note:

Grills built prior to serial number M1035495

will require the front control panel be reinstalled.

Loading Menu Items From USB

Once the proper software is loaded on the USB flash
drive, the next control board can be programmed
from the USB flash drive.

Step 1

Repeat Steps 1 through 5 from “Loading Store Menu
Items to USB.”

Step 2

Press the LOAD MENU FROM USB key.

Step 3

The control can display up to 5 different menu
options loaded on the USB flash drive. Select the
key for the correct menu to load. The control will
display “DONE” at the bottom of the screen when
the menu is loaded.

Step 4

Remove the USB flash drive from the USB port and
reinstall the USB cable cap on the USB connector.

Note:

Grills built prior to serial number M1035495

will require the front control panel be reinstalled.

Step 5

To load menu items from the USB flash drive to
another control board, repeat these software loading
procedures.

Summary of Contents for C819


















































Reviews:

No comments