Taylor C723 Service Manual Download Page 47

Page: 47 / 88

Model C723

Troubleshooting

PROBLEM

CAUSE

REMEDY

22. “Compressor on too long” fault

message.

a. The draw rate is set too fast.

a. Set the draw rate at 5 - 7‐1/2 oz. of

product per 10 seconds.

b. Inadequate air flow.

b. Make sure there is sufficient air

space surrounding the unit (see
“Specifications”).

c. Faulty blower baffle.

c. Repair or replace the blower baffle.

d. Inadequate AXV settings.

d. Set AXV at proper setting.

(See Running Specifications.)

23. “Product Door Off” message is

displayed.

a. The door is off or is loose.

a. Install the door and tighten the

hand screws.

b. Door switch is faulty.

b. Replace the switch.

c. The door switch is not properly

installed.

c. Make sure the door switch is fully

inserted.

d. The 24V relay is faulty.

d. Replace the relay.

e. There is low voltage from the 24V

transformer.

e. Check the power supply

connections/shorts. Replace
transformer.

Summary of Contents for C723

























































































Search results

Summary of Contents for C723

Reviews:

Taylor C723, Service Manual, Page: 47 / 88

Search results

Summary of Contents for C723

Reviews: