Taylor C723 Service Manual Download Page 38

Page: 38 / 88

Controls, Systems and Operations

Model C723

131028

Jumper Pin Chart - UVC4

Feature

Left Interface

X53451-SER

Right Interface

X53451-SER

Force Brush Clean Status

Syrup Heater Enable

Open All Left Solenoids

Open All Right Solenoids

Clock/Calendar Override

Force Glycol Pump On

59F Fault Detection Enable

W2**

Standby Stir Cycle Disable

Reduced Mix Low Sensitivity

Reduced Mix Out Sensitivity

7C/45F 90 Min. Cool Phase

Unused

Disable Control Panel (Self Serve)

J10 - 7 & 8

** Jumper initially installed at factory.

UVC4 Control Feature

Jumper

>41F for 4 hours & >45 for 1 hr

JP1 - 1 & 2**

Reserved (do not install)

JP1 - 3 & 4

Domestic/International

(Note 3)

JP2 - 1 & 2 **

Reserved (do not install)

JP3 - 1 & 2

Reserved (do not install)

JP4 - 1 & 2

Proximity Sensor

(Note 4)

JP5 - 1 & 2**

Reserved (do not install)

JP6 - 1 & 2

Reserved (do not install)

JP7 - 1 & 2

Reserved (do not install)

RTCK - 1 & 2

Reserved (do not install)

DBGEN - 1 & 2

** Jumper initially installed at factory.

Personality Board

0 - 6 Beater Motor Amperage
(do not use)

0 - 12 Beater Motor Amperage

B**

** Jumper initially installed at factory.

Notes:

Left and right are determined while facing the
front of machine.

Specified feature is established when the
jumper is installed.

International mode (jumper removed) enables
direct use of Heat and Standby keys and
hopper temperature display.

Jumper should be installed on shake machines
to enable proximity sensor. It is not active on
soft serve units; jumper can remain installed.

Summary of Contents for C723

























































































Search results

Summary of Contents for C723

Reviews:

Taylor C723, Service Manual, Page: 38 / 88

Search results

Summary of Contents for C723

Reviews: