Taylor C723 Service Manual Download Page 44

Page: 44 / 88

Troubleshooting

Model C723

General Troubleshooting Guide

PROBLEM

CAUSE

REMEDY

1. Compressor will not run.

a. The power switch is in the “OFF”

position.

a. Place the switch in the “ON”

position.

b. An error has been made in key

pad selection.

b. Press the correct key for AUTO

operation.

c. The contactor is faulty.

c. Replace the contactor.

d. The compressor has burned out.

d. Replace the compressor.

e. The fuse or circuit breaker has

blown.

e. Replace the fuse, or turn on the

breaker.

Tripped overload (compressor).

Place the power switch in the
“OFF” position. Allow the
compressor to cool and the
overload to close before returning
the power switch to the “ON”
position.

g. Off on reset (beater motor).

g. Press the reset button.

2. Unit operates long (cycles off on

the 11 minute safety timer.

a. Dirty condenser.

a. Clean the condenser.

b. Scraper blades are worn.

b. Replace scraper blades.

c. Shortage of refrigerant.

c. Repair the leak and recharge the

unit.

d. Air in the system.

d. Purge and recharge the system.

3. Head pressure is too high.

a. Condenser is dirty.

a. Clean condenser.

b. Water valve is out of adjustment or

is restricted.

b. Check the adjustment and the

water supply.

c. Insufficient air space around unit.

c. Make sure there is sufficient air

space surrounding the unit (see
“Specifications”).

d. Refrigerant overcharge.

d. Correct refrigerant charge.

e. Blower is faulty.

e. Replace the blower.

4. Head pressure is too low.

a. Refrigerant shortage.

a. Repair leak and recharge.

5. Liquid line is hot.

a. Shortage of refrigerant.

a. Repair leak and recharge.

6. Excessive mix leakage through

the rear of the unit into the drip
pan.

a. Worn or missing drive shaft seal.

a. If worn, nicked, or missing, replace

the drive shaft seal.

b. Inadequate lubrication.

b. Lubricate properly.

c. Drive shaft rotates forward.

c. Check gear alignment.

Summary of Contents for C723

























































































Search results

Summary of Contents for C723

Reviews:

Taylor C723, Service Manual, Page: 44 / 88

Search results

Summary of Contents for C723

Reviews: