Brakes
Page 61
MC-425-13
C0-425-48
REAR BRAKE
Service Limits
Refer to the table at the end of this section
Note: Service Limits are listed in a table at the end of
this section.
Inspection
1: Raise the front of the vehicle and support with jack
stands.
2: Remove the front wheels.
3: Measure the brake lining (not including the metal
backing plate) of each pad at it’s thinnest point. If
any one of the brake pads are equal to or less that
the service limit then all pads should be replaced.
4: Measure the rotor thickness in three places. If the rotor thickness is less than the service limit then the rotor
must be replaced.
5: Measure the rotor runout. If the runout exceeds the service limit, then the rotor must be resurfaced. After
resurfacing the rotor, measure the rotor thickness. If the rotor thickness is less than the service limit, then the
rotor must be replaced.
6: Lower the vehicle.
7: Reconnect the battery, remove the blocks from behind the wheels and test drive.
Replace Pads
Note: Installing new brake pads will raise the brake fluid level in the master cylinder.
1: Thoroughly clean the area around the master cylinder cap.
2:
Remove fluid from the master cylinder until it is 1/2 full.
3: Raise the rear of the vehicle and support with jack stands.
4: Remove the tire/wheel assembly. Refer to Tires and Wheels section for information on removing the tire and
wheel assembly.
5: Remove the brake body bolts and discard the lock nuts and brake pads.
6: Remove the spacer bushings from the mounting bracket and discard.
7: Inspect the brake rotor. Refer to Inspect the Service Brake section for information regarding inspecting the
brake rotor.
8: Inspect the spacers and replace if any wear or damage is found.
9: Inspect the park brake pin. Should slide freely inside the brake body. Clean or replace the pin and bushing if
required.
10: Install new spacer bushings in the mounting bracket.
11: Back off the parking brake adjustment.
12:
Install new brake pads in reverse order. Torque the brake body per specification at the end of this section.
13: Repeat this procedure for the other wheel.
14: Install the tire/wheel assembly and lower the vehicle to the ground.
15: Fill the master cylinder to the proper level. Refer to Check Master Cylinder Fluid section for information
regarding the correct master cylinder fluid level.
16: Reconnect the battery, remove the blocks from behind the wheels and test drive.
This section is one section of a complete service
manual. Before starting any procedure, read all
warnings and instructions that are located in the
Service Guidelines chapter.
WARNING
Summary of Contents for C0-425-48
