Tatung TAW-A70FD Service Manual Download Page 4

Page: 4 / 41

2. STRUCTURE OF THE WASHING MACHINE

STRUCTURE

•

GROUND WIRE

In case of 3-wire

power cord, ground

wire will not be

provided

•

POWER CORD

•

DRAIN HOSE

•

LINT FILTER

•

COLD WATER TAP

After using the washer,

close the water tap

•

DETERGENT CASE

•

ADJUSTABLE LEG

•

SOFTENER INLET

•

BLEACH INLET

•

CONTROL PANEL

•

POWER SWITCH

•

PULSATOR

Accessories

The parts and features of your washer are illustrated on this page.
Become familiar with all parts and features before using your washer.

NOTE

• The drawing in this book may vary from your washer model. They are designed to show the different fea-

tures of all models covered by this book, Your model may not include all features.

• Page references are included next to same features.

Refer to those pages for more information about the features.

UNDER COVER(OPTION)

DRAIN HOSE

INLET HOSE(OPTION)

NON PUMP MODEL

Summary of Contents for TAW-A70FD










































Search results

Summary of Contents for TAW-A70FD

Reviews:

Related manuals for TAW-A70FD

Brands by name

Popular brands

Tatung TAW-A70FD, Service Manual

Search results

Summary of Contents for TAW-A70FD

Reviews:

Related manuals for TAW-A70FD

Brands by name

Popular brands