Tatung TAW-A70FD Service Manual Download

Page: 29 / 41

TROUBLE SHOOTING

PROBLEM

THE INDICA-

TOR

LAMPS(L.E.D)

DO NOT LIGHT

UP WHEN THE

POWER BUT-

TON IS

PRESSED.

PROGRESS
LAMPS(LED)
DO NOT LIGHT
UP.

MOTOR
ROTATES
WHEN
START/HOLD
BUTTON IS
NOT
PRESSED.

ABNORMAL
NOISE DUR-
ING WASH
PROCESS.

CHECK POINT

Is the plug connect-ed
to electric outlet?

Is the condition of
power button good?

Is the connector of the
P.C.B. ASS’Y connect-
ed properly?

Do you press
START/HOLD button?

Does the pressure switch
operate normally?

Check the output voltage
of P.C.B ASS’Y

Is the strange noise gen-
erated when the pulsator
rotates in TEST MODE
of P.C.B ASS’Y?

Is the V-belt worn out?

CAUSE

SOLUTION

Connect the plug.

Change P.C.B ASS’Y.

Change Fuse

Connect the connector
properly.

Change P.C.B ASS’Y.

Press START/HOLD but-
ton.

Replace P.C.B ASS’Y.

Change the pressure
switch.

Change P.C.B ASS’Y.

Remove the foreign mat-
ter.

Change the V-belt.

Power button is defective

Improper connection of
the connector.

P.C.B. ASS’Y is defec-
tive.

P.C.B ASS’Y is defective.

Pressure switch is defec-
tive.

P.C.B ASS’Y is defective

There is foreign matter
between pulsator and
tub.

V-belt is defective.

YES

Abnormal

YES

Is Fuse opended?

Concerning Operation

Summary of Contents for TAW-A70FD










































Search results

Summary of Contents for TAW-A70FD

Reviews:

Related manuals for TAW-A70FD

Brands by name

Popular brands

Tatung TAW-A70FD, Service Manual

Search results

Summary of Contents for TAW-A70FD

Reviews:

Related manuals for TAW-A70FD

Brands by name

Popular brands