Taski swingo 1255B Power Technical Manual Download Page 49

Page: 49 / 110

GTS

Technical Manual

19. April 2010

Edition: V1.00/2010

5-28

05.0 s

go 1255 B Power - me

anics

.fm

5.1.7 Brush drive unit

5.1.7.1 Replacing of brush drive unit

Picture 31: Brush drive replacing

For easier access lower the brush unit.

Remove

•

Unlock battery compartment by removing screws of locking

system.

•

Open battery compartment.

•

Unscrew brush housing fixation screws.

•

Remove the brush housing from the brush drive unit.

•

Disconnect the fresh water hoses from the brush unit.

•

Disconnect the brush motor wires from the power electronics.

•

Remove RH circlip (06/112) from the axle (06/114).

•

Remove the axle.

•

Remove the retaining ring (06/110) on the LH and RH side

from the bolts (06/115), holding brush drive unit to the cradle.

Picture 32: Brush drive fixation

Summary of Contents for swingo 1255B Power


































































































Search results

Summary of Contents for swingo 1255B Power

Reviews:

Related manuals for swingo 1255B Power

Brands by name

Popular brands

Taski swingo 1255B Power, Technical Manual

Search results

Summary of Contents for swingo 1255B Power

Reviews:

Related manuals for swingo 1255B Power

Brands by name

Popular brands