Taski swingo 1255B Power Technical Manual Download Page 29

Page: 29 / 110

GTS

Technical Manual

19. April 2010

Edition: V1.00/2010

5-8

05.0 s

go 1255 B Power - me

anics

.fm

5.1.1.5 Replacing of tank cover

Picture 7: Tank cover

Remove

•

Unscrew dashboard fixation.

•

Remove dashboard and disconnect all cables.

•

Remove the 3 screws of handle cover.

•

Remove handle cover.

•

Unplug hour counter wires from the hour counter or the cover.

•

Remove screws (01/103) of throttle lever bracket.

•

Thread out hall sensor ribbon cable and remove the complete

throttle lever system.

•

Unscrew handle fixation to the tank cover (01/106 and 01/

107).

•

Remove handle from tank cover.

•

Unscrew and remove rear panel (09/103).

•

Open the tank cover.

•

Loosen the screw (01/107) on the tank cover on the support

side (RH).

•

Loosen the screw on the other side (LH).

•

Close the tank cover.

•

Open the tank cover without base plate.

Picture 8: Base plate

•

Disconnect vacuum motor cable at connection block (cable to

Summary of Contents for swingo 1255B Power


































































































Search results

Summary of Contents for swingo 1255B Power

Reviews:

Related manuals for swingo 1255B Power

Brands by name

Popular brands

Taski swingo 1255B Power, Technical Manual

Search results

Summary of Contents for swingo 1255B Power

Reviews:

Related manuals for swingo 1255B Power

Brands by name

Popular brands