TASCAM CD-6010
11
2 – Names and Functions of Parts
9
MENU [PITCH] button
Press this button to start menu mode. When in menu
mode, press this button to exit menu mode. (See
"Menu operation basics" on page 19.)
To enter pitch adjustment mode, press this button
when in shift mode (when the
SHIFT
indicator is lit) or
while pressing the
SHIFT
button. (See "Pitch control
playback" on page 27.)
0
SPEAKER, ON/OFF switch, LEVEL knob
& PHONES jack
Use the built-in mono speaker or stereo headphones
to monitor the playback signal without needing to
connect speakers.
Use the
SPEAKER
switch to turn the built-in speaker
ON
and
OFF
.
When headphones are connected, this speaker is
disabled regardless of the
SPEAKER
switch position.
Connect stereo headphones to the standard stereo
PHONES
jack.
Use the
LEVEL
knob to adjust the output level of the
built-in speaker and the headphones.
CAUTION
Before connecting headphones, turn the LEVEL knob to
minimize the volume. Failure to do so might cause sudden
loud noises, which could harm your hearing or result in other
trouble.
q
REMOTE jack (2.5mm TRS)
Use this jack to connect a TASCAM RC-3F footswitch
or TASCAM RC-20 direct playback remote control (sold
separately). Use a remote control for flash starting and
stopping playback, for example.
w
CLEAR button
Press this button to cancel the input of a number
button.
When the CUE mode is ON, press a number button
while pressing and holding this button to clear the
corresponding cue point.
Press and hold when the program menu is open to
clear all programs.
e
Number buttons
Use these number buttons to designate track numbers
to select songs. Input two digits for audio CDs and
three digits for data CDs. (See “Designating track
numbers” on page 22.)
When CUE mode is on, use the number buttons to
add, recall and delete cue points (up to 20). (See "Cue
function" on page 25.)
When the flash start function is on, use the number
buttons to flash start tracks or cue points.
Use the
+10
button to switch between 1-10 and 11-20
for flash start program numbers, track numbers and
cue numbers.
r
Force eject hole
If the tray will not open ordinarily, insert a fine rod,
such as a paperclip, here and press to open the tray.
CAUTION
Always turn the power OFF before using the force eject hole.
t
CUE button
Press to turn cue mode ON/OFF.
y
FLASH button
Press to turn the flash start function ON/OFF.
u
ª
STOP [INTRO CHECK] button
Press to stop playback.
If the incremental playback function is activated, press
this button during playback to pause at the beginning
of the next track.
When stopped, to activate the intro check mode,
press this button when in shift mode (when the
SHIFT
indicator is lit) or while pressing the
SHIFT
button.
When this mode is activated, press the
Á
(play)
button to play the first 10 seconds of each track in
succession. (See “Intro check mode” on page 27.)
i
CALL button
Press this button to return to the point where playback
was last started and pause.
o
Á
PLAY button and indicator
When stopped, press this button to start playback. (The
indicator lights during playback.)
When paused, press this button to resume playback.
During playback, press this button to return to the
point that was previously set. (See “Skip back playback”
on page 30.)
p
π
PAUSE button and indicator
Press during playback to pause (indicator lights).
When the auto-cue function is on, press when stopped
to pause at the instant when sound begins in track 1.
When the auto-cue function is off, press when stopped
to pause at the beginning of track 1.
a
SEARCH
Ô
/
[AUTO CUE/AUTO READY]
buttons
During playback or when paused, press the
Ô
button to search backward, and press the
button
to search forward. (See “Using the SEARCH buttons” on
page 23.)
When in program setting mode, use these to select the
program number. (See “Program playback” on page
28.)
To turn the auto-cue function on and off, press the
Ô
button when in shift mode (when the
SHIFT
indicator is lit) or while pressing the
SHIFT
button. (See
“Auto-cue function” on page 24.)
To turn the auto-ready function on and off, press the
button when in shift mode (when the
SHIFT
indicator is lit) or while pressing the
SHIFT
button. (See
“Auto-ready function” on page 24.)
