Tarm Biomass Bonus Plus 30 Installation And Operation Manual Download Page 35 | Manualshive

Page: 35 / 55

Tarm Biomass Bonus Plus 30 Installation And Operation Manual Download Page 35

Bonus Plus Instructions Tarm Biomass 1-800-782-9927 Version 11/14 Page 35

Boiler Operation, Maintenance, and Service > Cleaning and Maintenance

NOTE

Please inspect the draft fan carefully – even a thin coating of ash significantly reduces the air
flow and must be removed.

NOTE

If the fan motor is blocked because of lack of cleaning, the motor can be damaged.

4.10.2 Cleaning the Induction Fan

1.  Shut off the power supply to the boiler.
2.  Remove the fan housing.
3.  Remove the wing-nuts holding the fan in place and

remove the fan.

4. Clean the fan blades, fan housing, and the flue gas

sensor well (pipe). See pictures on following page.

For inspection and cleaning, remove the induced draft fan on the back of the boiler. Check for build-
up and damage 2-3 times per year. Clean the draft fan wheel inside and out using a stiff brush. Re-
move ash deposits from the induced draft fan housing using a putty knife, and vacuum loosened mate-
rial from the housing and draft fan. Check the silicone gasket for condition and replace if necessary.

When the chimney connector is connected vertically directly under the chimney, the fan must always
be removed and cleaned after each cleaning of the chimney.

Fig. 4.13

WARNING

Before accessing the fan shut off the power supply to the boiler.

«
...
33
34
35
36
37
...
»

Summary of Contents for Bonus Plus 30
























































Reviews:

No comments