manualshive.com logo in svg

Tarm Biomass Bonus Plus 30, Installation And Operation Manual, Page: 22 / 55

Share
Download
Tarm Biomass Bonus Plus 30 Installation And Operation Manual Download Page 22

 

Bonus Plus Instructions      Tarm Biomass   1-800-782-9927   Version 11/14          Page 22 

3.4.3 System Plumbing 

There are numerous possibilities for connecting your Bonus Plus and thermal storage system to your 
home heating system. Tarm Biomass provides diagrams as concept diagrams only. Final design, in-
stallation, and code compliance details are the responsibility of the designer/installer of the system. 

3.4.4 Pipe Connections – Choice of Material

 

 

Copper or black iron pipe may be used. Do not use galvanized iron pipe. The supply and return flows 
must be carefully insulated to avoid heat loss. 
 

3.4.5 Immersion Tubes and Wells

  

Remember to install the immersion tubes provided in the corresponding well. 

Remember to plug 

wells which are not used in the chosen form of installation. 
 

3.4.6 Expansion Tank  

The size of the expansion tank is determined by the total water content of the heating system. 

 
3.4.7 Pump Size 

The size of the circulation pump is determined by the size of the system and the pipe dimensions. 
 

3.4.8 Installing the Circulator Aquastat 

The Honeywell L6006A aquastat provided is installed to activate the boiler’s circulator in case there is 
a temperature rise after the boiler has shutdown.  

                                                                

Boiler Installation & Start-up >  Connections to the Boiler 

 

NOTE 

Any radiant tubing used with the Solo Plus boiler must have an oxygen barrier! Non oxygen 
barrier tubing must be separated from the boiler using a heat exchanger. 

NOTE 

The Normal Operating pressure is between 12-15psi. 

First, remove the boiler’s top panel. 
Next, remove the side panel (can be left 
or right) Remove the ½” fitting (Shown 
in image). 

 

Install the new ½” sensor well. 

 

Summary of Contents for Bonus Plus 30
























































Reviews:

No comments