Tar River BPD-680 Operator'S Manual Download Page 22 | Manualshive

Page: 22 / 36

background image

22

BPD

-

680/750 Post Hole Driver

Notes:

This chart is an approximate estimate of torque values.

Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.

Fasteners must always be replaced with the same grade as specified in the manual.

Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for Metric hardware.

Make sure that fastener threads are clean and that you properly start thread engagement.

Torque Specifications

«
...
20
21
22
23
24
...
»

Summary of Contents for BPD-680





































Reviews:

No comments

Related manuals for BPD-680

Brand: Velp Scientifica Pages: 16

Brand: Velp Scientifica Pages: 2

Brand: Velp Scientifica Pages: 32

Brand: Velleman-Kit Pages: 32

Brand: Parker Research Corp Pages: 3

Brand: Fast Pages: 60

Brand: SAC Pages: 2

INTRAmatic 31 ES

Brand: KaVo Pages: 52

Brand: Kelvin Pages: 30

Firefly Low Voltage Lighting System

Brand: Ultra Pages: 2

Brand: Lumination Pages: 2

Brand: Knightsbridge Pages: 4

Brand: Studiomaster Pages: 10

Brand: Cameo Pages: 188

Brand: Calex Pages: 17

Brand: Synca Pages: 12

Brand: Omni Pages: 20

Brand: Malibu Boats Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands