b) Battery charging
• Before first operation, it is recommended to fully charge the product once.
• Charge the portable charger at the latest when only one LED lights up or the battery charge
level falls below 25 %. Charge the portable charger via one input only.
Never use two inputs for charging.
• The charger can be charged via the Micro-USB or the USB-C™ connection. To charge the
portable charger, a USB charger (not included in delivery) is required. The delivery includes
a USB charging cable for connection to the Micro-USB input (1).
• Connect the Micro-USB plug to the Micro-USB input. Connect the USB-A plug of the USB
charging cable to a USB-A port of a USB charger (not included in the delivery). Observe the
technical data.
A USB charger with 2 A (Micro-USB input) or with 3 A (USB-C™ connection) is
recommended for the portable charger’s input current. If a lower input current is
used, charging takes longer. An input current higher than 2 A (Micro-USB) or 3 A
(USB-C™) will not reduce the charging time, however, since the input current is
limited at each connection.
• Charging the portable charger with a 2 A USB charger via the Micro-USB input at a residual
capacity of the battery of approx. 20 % may take approx. 8.5 - 9 hours. Charging with a 3 A
USB charger via the USB-C™ connection takes approx. 6.5 - 7.5 hours (battery level approx.
20 %). During charging, the LEDs flash to indicate the current battery status.
• As soon as the battery is fully charged, the LEDs of the battery status indicator light up
constantly.
• Disconnect all the cables.
c) Charging a mobile device
• You can charge the portable charger while charging your mobile devices.
Simultaneous charging of the portable charger and connected mobile devices is not
recommended, since in this case the battery of the portable charger continuously
discharges. Charging the internal rechargeable battery of the portable charger then
takes longer.
• Through the integrated circuit (smart IC), the portable charger recognizes at the USB outputs
the required maximum charging current for the connected devices.
• Connect the USB-A connector of the USB charging cable with the USB-A output (2). If
your mobile device features a USB-C™ connection, you can connect a charging cable with
a USB-C™ plug (not included) to the USB-C™ connection (5). Devices with a USB-C™
connection normally permit a higher charge current and thus charge more quickly than
devices with a Micro-USB connection.
The maximum charging current (3 A) is distributed to the USB outputs when both
outputs are used. Therefore, check how much charging current your mobile device
requires.
• Connect the Micro USB plug to your mobile device.
• During charging, the LEDs remain lit to indicate the portable charger’s current battery status.
• Disconnect the USB charging cable from the portable charger and from the connected device
to pause or stop charging. When the connected mobile device is fully charged or the USB
charging cable is unplugged, the battery status indicator goes out.
d) Torch function
• Double-click the function key (6) to turn on the integrated LED torch (4).
• Briefly press the function key again to turn off the torch. The LED torch goes out.
Care and cleaning
• Before cleaning, disconnect the product from the connected devices and from the power
supply.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the casing or cause the product to malfunction.
• Use a dry, lint-free cloth to clean the product.
• Avoid contact with water or other liquids when cleaning.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. Always dispose of the product according to the relevant statutory
regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
Input voltage/current ..................... Micro-USB input 5 V/DC, 2 A
USB-C™ input 5 V/DC, 3 A
Output voltage/current .................. Micro-USB output 5 V/DC, 2 A
USB-C™ output 5 V/DC, 3 A,
both USB outputs combined 3 A max.
Internal rechargeable battery ........ lithium-polymer (LiPo) / 16000 mAh
LED light colour temperature ........ 9000 K
Operating conditions ..................... 0 to +40 °C, 20 - 90 % RH
Storage conditions ........................ -10 to +55 °C, 20 - 90 % RH
Dimensions (L x W x H) ................ 150 x 73 x 17 mm
Weight .......................................... 359 g
These operating instructions are published by CEI Conrad Electronic International (HK) Limited, 18th floor, Tower 2,
Nina Tower, no. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong. All rights including translation reserved.
Reproduction by any method (e.g. photocopying, microfilming or capture in electronic data processing systems) requires
prior written approval from the editor. Reprinting, also in part, is prohibited. The operating instructions reflect the current
technical specifications at time of print.
Copyright 2018 by CEI Conrad Electronic International (HK) Limited
*1004BTF_1601918_v1_0418_02_hk_m_en
Distributed by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau
