manualshive.com logo in svg

TAO F125, Owner'S Manual

Share
Download
TAO F125 Owner'S Manual Download Page 15

The adjustable speed limiter screw must be installed for operation. Failure to install a speed limiter 
screw may result in water or dirt ingestion and potential damage to the vehicle.

FRONT BRAKE LEVER
The front brake lever is located on the right handlebar. To apply the front brake, pull the brake lever toward the 
handlebar grip. 

REAR 

FOOT 

BRAKE LEVER

The rear 

foot 

brake lever is located on the 

right foot rest 

. To apply the rear brake, 

push

 the brake

 with your 

right foot 

toward the 

ground

. 

NOTICE

 SPEED LIMITER ADJUSTMENT

1

.

 Locknut

2

.

 Adjustment Screw

3

.

 Adjustment 

R

ange

Adults should always limit maximum restricted 

speed within the ability and capacity of th

e

 child to 

operate the ATV safely. Never allow the child to 

adjust the speed limiter screw

.

To increase top speed

 

SPEED LIMITER

The 

F125

  ATV

  is  equipped 

with  a 

vehicle  speed  limiter  adjusting  screw.  Beginning  riders  should start with slowest 

setting to learn how to control this vehicle. Once the operator has demonstrated mastery of the ATV, the  supervising 
adult  can  adjust  speed  limiter  screw  to  increase  the  top  speed  .  The  vehicle  speed  limiter keeps  the  throttle  from 
fully  opening,  even  when  the  throttle  lever  is  pushed  to  the  maximum.  The adjusting screw may be gradually 
turned out as the beginner becomes more familiar with operating this ATV. 

To decrease top speed 

1. Loosen locknut (#1).

2. To decrease the top speed of the ATV turn the adjustment screw clockwise. (#2).

3. Tighten the locknut to set adjustment screw in desired position(#1).

1. Loosen locknut (#1).

2. To increase the top speed of the ATV turn the adjustment screw counter 

clockwise. (#2).

3. Tighten the locknut to set adjustment screw in desired position(#1).

6

Summary of Contents for F125













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands