Tannoy V12HP, Owner'S Manual

Page: 11 / 28

11
9.0 TECHNICAL SPECIFICATIONS
SYSTEM
System Type
Frequency Response (-3dB)
1
Full Range Mode
Frequency Range (-10dB)
1
Full Range Mode
Frequency Response (-3dB)
1
High Pass Mode
Frequency Range (-10dB)
1
High Pass Mode
Rated Maximum SPL
Dispersion (-6dB)
Driver Complement
Directivity Factor (Q)
Directivity Index (DI)
Distortion
10% Full Power (8.9V)
250Hz
1kHz
10kHz
1% Full Power (2.8V)
250Hz
1kHz
10kHz
Crossover
Notes
CONSTRUCTION
Enclosure
Finish
Connectors
Controls & Indicators
Fittings
Dimensions
Weight
ELECTRONICS
Maximum signal input for clip
Output noise
Efficiency
Damping Factor
Distortion
Input Impedance
Protection systems
Over Current
Temperature
Brownout
Mains
Indicators
Number of channels
System Type
PSU SPECIFICATIONS
Input Connector
Voltage Selection
Type
Efficiency
Input voltage
Mains fuse
Fuse type
Other features
Power V6
Full Range - Vented
85Hz - 35kHz
78Hz - 45kHz
120Hz - 35kHz
100Hz - 45kHz
107dB (average) 113dB (peak)
90 Degrees Conical
1 x 150mm (6 ) Dual Concentric™
5.6 averaged 1kHz to 10kHz
7.0 averaged 1kHz to 10kHz
2nd Harmonic 3rd Harmonic
2.64% 0.31%
0.22% 0.45%
1.87% 0.29%
2nd Harmonic 3rd Harmonic
0.63% 0.31%
0.06% 0.23%
0.78% 0.26%
1.6kHz Passive
11.3 litre MDF, Vented,
Internally Braced
Textured Black or White paint
(Custom colours on request).
Powder Coated Steel Grill
(reticulated foam behind)
1 x female XLR (input),1 male XLR
(link), 1 x Neutrik Powercon
Level Control
Power LED (Blue)
Signal LED (Green)
Limit LED (Red)
Full Range / HighPass Switch (110Hz)
Power Switch
4 x M6 bracket inserts,
2 x M6 yoke bracket inserts
337 x 252 x 240mm
13.26 x 9.92 x 9.44”
8.5kg (18.7lbs)
Input attenuator at
minimum - +18dBu
Input attenuator at
Maximum - +5dBu
-105dB unweighted, referenced to
maximum output (22kHz bandwidth)
>90% typically
400 ref 8 Ohms
<0.05% @ 1kHz -3dB output
(22kHz bandwidth)
5.6kOhms unbalanced,
11.2kOhms balanced
Excessive over current causes
shutdown
Limiters applied
Automatic protection & recovery
Inrush current limiting
1x Limit LED, 1x Signal LED &
1x Power LED
one
Class D
Locking Neutrik Powercon
Automatic (115 / 230V, 45 - 65Hz)
High current, high freq. switch-mode
>90% typical
100V / 115V / 230V n/-10%
External
T10AT
Automatic soft-start
1. Average over stated bandwidth. Measured at 1 metre on axis.
2. Unweighted pink noise input, measured at 1 metre in an anechoic chamber
A full range of measurements, performance data, and Ease!™ Data can be downloaded from www.tannoy.com Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications, which Tannoy reserves the right to alter without prior
Power V8
Full Range - Vented
80Hz - 30kHz
67Hz - 40kHz
120Hz - 30kHz
100Hz - 40kHz
113dB (average) 119dB (peak)
90 Degrees Conical
1 x 200mm (8 ) Dual Concentric™
6.8 averaged 1kHz to 10kHz
7.9 averaged 1kHz to 10kHz
2nd Harmonic 3rd Harmonic
0.12% 0.15%
0.23% 0.84%
1.35% 0.16%
2nd Harmonic 3rd Harmonic
0.16% 0.14%
0.09% 0.53%
0.53% 0.17%
1.7kHz Passive
17 litre vented, 15mm (5/8 ) birch
plywood and 15mm (5/8 ) MDF front
baffle.Vented, Internally braced.
Textured Black or White paint
(Custom colours on request).
Powder Coated Steel Grill
(reticulated foam behind)
1 x female XLR (input), 1 male XLR
(link), 1 x Neutrik Powercon
Level Control
Power LED (Blue)
Signal LED (Green)
Limit LED (Red)
Full Range / HighPass Switch (110Hz)
Power Switch
4 x M10 Flying inserts, 2 x M10 yoke
bracket inserts 1 x recessed carrying
handle Blanking plate for optional
VTH, pole mount
338 x 280 x 275mm
15.28x11.02x10.83”
10.5kg (23.1lbs)
Input attenuator at
minimum - +18dBu
Input attenuator at
Maximum - +5dBu
-105dB unweighted, referenced to
maximum output (22kHz bandwidth)
>90% typically
400 ref 8 Ohms
<0.05% @ 1kHz -3dB output
(22kHz bandwidth)
5.6kOhms unbalanced,
11.2kOhms balanced
Excessive over current causes
shutdown
Limiters applied
Automatic protection & recovery
Inrush current limiting
1x Limit LED, 1x Signal LED & 1x
Power LED
one
Class D
Locking Neutrik Powercon
Automatic (115 / 230V, 45 - 65Hz)
High current, high freq. switch-mode
>90% typical
100V / 115V / 230V n/-10%
External
T10AT
Automatic soft-start
Power V12
Full Range - Vented
70Hz - 25kHz
55Hz - 38kHz
100Hz - 30kHz
80Hz - 38kHz
120dB (average) 126dB (peak)
90 Degrees Conical
1 x 300mm (12 ) Dual Concentric™
8.2 averaged 1kHz to 10kHz
8.8 averaged 1kHz to 10kHz
2nd Harmonic 3rd Harmonic
0.56% 0.23%
2.36% 1.88%
2.68% 0.08%
2nd Harmonic 3rd Harmonic
0.14% 0.14%
0.38% 0.94%
1.03% 0.05%
1.4kHz Passive
37.5 litre vented, 15mm (5/8 ) birch
plywood and 15mm (5/8 ) MDF front
baffle.Vented, Internally braced.
Textured Black or White paint (Custom
colours on request).
Powder Coated Steel Grill (reticulated
foam behind)
1 x female XLR (input), 1 male XLR
(link), 1 x Neutrik Powercon
Level Control
Power LED (Blue)
Signal LED (Green)
Limit LED (Red)
Full Range / HighPass Switch (110Hz)
Power Switch
8 x M10 Flying inserts, 8 x M10 yoke
bracket inserts 3 x recessed carrying
handles (2 side & 1 rear) Blanking
plate for optional VTH, pole mount
486 x 370 x 375mm
19.13x14.57x15.5”
23kg (50.6lbs)
Input attenuator at
minimum - +18dBu
Input attenuator at
Maximum - +5dBu
-105dB unweighted, referenced to
maximum output (22kHz bandwidth)
>90% typically
400 ref 8 Ohms
<0.05% @ 1kHz -3dB output (22kHz
bandwidth)
5.6kOhms unbalanced,
11.2kOhms balanced
Excessive over current causes
shutdown
Limiters applied
Automatic protection & recovery
Inrush current limiting
1x Limit LED, 1x Signal LED & 1x
Power LED
one
Class D
Locking Neutrik Powercon
Automatic (115 / 230V, 45 - 65Hz)
192kHz Syncronised to DSP
High current, high freq. switch-mode
>90% typical
100V / 115V / 230V n/-10%
External
T10AT
Automatic soft-start
Power V12HP
Full Range - Vented
71Hz - 23kHz
62Hz - 28kHz
100Hz - 23kHz
80Hz - 28kHz
124dB (average) 130dB (peak)
75 Degrees Conical
1 x 300mm (12 ) PowerDual™
8.2 averaged 1kHz to 10kHz
9.1 averaged 1kHz to 10kHz
2nd Harmonic 3rd Harmonic
0.04% 0.58%
0.80% 2.64%
2.11% 0.11%
2nd Harmonic 3rd Harmonic
0.24% 0.67%
1.80% 4.11%
5.21% 0.21%
1.75kHz Passive
37.5 litre vented, 15mm (5/8 ) birch
plywood and 15mm (5/8 ) MDF front
baffle.Vented, Internally braced.
Textured Black or White paint (Custom
colours on request).
Powder Coated Steel Grill (reticulated
foam behind)
1 x female XLR (input), 1 male XLR
(link), 1 x Neutrik Powercon
Level Control
Power LED (Blue)
Signal LED (Green)
Limit LED (Red)
Full Range / HighPass Switch (110Hz)
Power Switch
8 x M10 Flying inserts, 8 x M10 yoke
bracket inserts 3 x recessed carrying
handles (2 side & 1 rear) Blanking
plate for optional VTH, pole mount
486 x 370 x 375mm
19.13x14.57x15.5”
23kg (50.6lbs)
Input attenuator at
minimum - +18dBu
Input attenuator at
Maximum - +5dBu
-105dB unweighted, referenced to
maximum output (22kHz bandwidth)
>90% typically
400 ref 8 Ohms
<0.05% @ 1kHz -3dB output (22kHz
bandwidth)
5.6kOhms unbalanced,
11.2kOhms balanced
Excessive over current causes
shutdown
Limiters applied
Automatic protection & recovery
Inrush current limiting
1x Limit LED, 1x Signal LED & 1x
Power LED
one
Class D
Locking Neutrik Powercon
Automatic (115 / 230V, 45 - 65Hz)
High current, high freq. switch-mode
>90% typical
100V / 115V / 230V n/-10%
External
T10AT
Automatic soft-start
Power V15
Full Range - Vented
60Hz - 23kHz
47Hz - 26kHz
100Hz - 23kHz
80Hz - 26kHz
126dB (average) 132dB (peak)
75 Degrees Conical
1 x 380mm (15 )PowerDual™
7.8 averaged 1kHz to 10kHz
8.9 averaged 1kHz to 10kHz
2nd Harmonic 3rd Harmonic
1.00% 0.50%
1.40% 1.00%
3.98% 1.78%
2nd Harmonic 3rd Harmonic
0.32% 0.45%
0.45% 0.79%
3.16% 0.31%
Passive 1.4kHz
62 litre vented, 15mm (5/8 ) birch
plywood and 15mm (5/8 ) MDF front
baffle. Vented, Internally braced.
Textured Black or White paint (Custom
colours on request).
Powder Coated Steel Grill (reticulated
foam behind)
1 x female XLR (input), 1 male XLR
(link), 1 x Neutrik Powercon
Level Control
Power LED (Blue)
Signal LED (Green)
Limit LED (Red)
Full Range / HighPass Switch (110Hz)
Power Switch
8 x M10 Flying inserts, 8 x M10 yoke
bracket inserts 3 x recessed carrying
handles (2 side & 1 rear) Blanking
plate for optional VTH, pole mount
590 x 450 x 420mm
23.23x17.72x16.54”
35kg (77lbs)
Input attenuator at
minimum - +18dBu
Input attenuator at
Maximum - +5dBu
-105dB unweighted, referenced to
maximum output (22kHz bandwidth)
>90% typically
400 ref 8 Ohms
<0.05% @ 1kHz -3dB output (22kHz
bandwidth)
5.6kOhms unbalanced,
11.2kOhms balanced
Excessive over current causes
shutdown
Limiters applied
Automatic protection & recovery
Inrush current limiting
1x Limit LED, 1x Signal LED & 1x
Power LED
one
Class D
Locking Neutrik Powercon
Automatic (115 / 230V, 45 - 65Hz)
High current, high freq. switch-mode
>90% typical
100V / 115V / 230V n/-10%
External
T10AT
Automatic soft-start