Tannoy Ellipse 8 iDP Owner'S Manual Download Page 49 | Manualshive

Page: 49 / 56

background image

49

iDP

™

Display Messages

The following is an explanation of Error Messages, etc may appear on a Master monitor Display:-

"!" as "96 kHz Center!”

The "!" indicates that the monitor is not connected to the network. The volume is then automatically set to -50 dB for the
monitor not recognized in the network.

"+" as "96 kHz L Front+":

The "+" indicates that the monitor you are looking at is the System Controller.

>> A-Input Lo <<

This message is displayed in analog setups only and indicates that the Input level has been detected to be between -60dB
and -20dB for a period longer than 3 minutes. This is an indication to increase the Analog Input Gain.
Analog Input gain range:
+9dBu, +15dBu, +21dBu or 27 dBu.

>> A-Input Hi <<

This message is displayed in analog setups only and indicates that an Input level near 0dB is detected. (peaks @ 2 sec.
Above -1 dB). This is a warning and you should turn down the Analog input gain
Analog Input gain range:
+9dBu, +15dBu, +21dBu or 27 dBu.

>> PSU error <<

Displayed if the power supplies fails. The power will be turned off and the monitor will operate. Contact TANNOY Service
Department.

<Locked>

Displayed when a parameter is locked by the PC-iP

™

installer software and cannot be changed.

Parameter lock can only be unlocked with the PC-iP

™

software.

Standby

Displayed when no Input signal has been detected for the time specified in the

Utility Menu

. below -65 dB. The Amplifier

is turned off. Standby mode is released as soon a signal level above -65dB has been detected.

>> Power save <<

Displayed when no signal has been detected on all monitors on the network for the time specified in the

Utility Menu

.

Power is turned off. Exit this mode by pressing any key on system controller or adjusting volume from the remote.

«
...
47
48
49
50
51
...
»

Summary of Contents for Ellipse 8 iDP

























































Reviews:

No comments

Related manuals for Ellipse 8 iDP

Brand: 1byone Pages: 17

Brand: VocoPro Pages: 28

Force i Monitor

Brand: Electro-Voice Pages: 6

Brand: Valcom Pages: 1

Brand: Tannoy Pages: 11

HouseParty PG731

Brand: Gear4 Pages: 34

Brand: Parts Express Pages: 19

Brand: Behringer Pages: 11

Brand: KEF Pages: 2

LCD5710-2-AV - MultiSync - 57" LCD Flat Panel...

Brand: NEC Pages: 2

JADE SERIES JADE-C1

Brand: Wharfedale Pro Pages: 8

SoundFactor SF15i

Brand: JBL Pages: 2

Brand: Pyle Pages: 2

Brand: Wharfedale Pro Pages: 12

Brand: Fusion Pages: 3

Brand: KALI AUDIO Pages: 17

DTS99 SPEAKER SYSTEM

Brand: Altec Lansing Pages: 6

Brand: Kanto Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands