background image

TROUBLESHOOTING

If you are experiencing problems with this unit, in the first instance please carefully read the 
relevant sections of the User Manual and the Troubleshooting section below.  If you cannot 
solve your problem please contact your supplier for further assistance.

www.tanningessentials.co

PROBLEM

CAUSE

WHAT TO DO

My solution is 
bubbling from 
the cup

Seal is not in properly

Solution Cup is not screwed in 
correctly

The cup is cross-threaded

Solution cup is overfilled

Fit the gun seal correctly.

Unscrew and reattach the cup.

Unscrew and reattach the cup.

Empty some solution from the 
cup so it is half to 3/4 full. 

The air flow is 
cutting in an out

The filter is dirty

The power setting need 
adjusting 

Remove the filter from the base of 
the unit and rinse in warm water. 
Wait until filter is completely dry 
before refitting.

Increase the power on your system.

Power cord not attached

Electricity not turned on

Ensure that the power cord is 
pushed in firmly to the base of the 
unit and wall socket

Ensure that the power point is on

The Spray Unit 
will not turn on

Spray Cup is not tight enough

Too much solution

Nozzle may be blocked 

Tighten the solution cup 

Empty some solution from the 
cup so it is half to 3/4 full

Perform secondary maintenance 

The spray 
applicator is 
leaking

 

 

Summary of Contents for PROV

















Reviews: