Tangent Scale Models PS-2CD 4000 Instructions Manual Download | Manualshive

Page: 9 / 20

background image

Tangent Scale Models

PS-2CD 4000 Kit Assembly Instructions

9

8.

Attach the air reservoir assembly to the B end slope sheet:

Note that there are two holes for

the air reservoir part to mount into on the slope sheet part added earlier. Also note the hole on
top of the stem over the draft gear for the mounting of the AB Valve. Glue the assembly in
place.

«
...
7
8
9
10
11
...
»

Summary of Contents for PS-2CD 4000





















Reviews:

No comments

Related manuals for PS-2CD 4000

Brand: Laser Pegs Pages: 3

Brand: Laser Pegs Pages: 2

ALBATROS D.Va 25e

Brand: E-FLITE Pages: 40

Brand: Xray Pages: 40

MARINER 40 MK II ARF

Brand: Lanier R/C Pages: 14

Brand: Fisher-Price Pages: 6

IDF Merkava Mk.IV

Brand: Eduard Pages: 6

Brand: Radica Games Pages: 2

Brand: Mardave Pages: 12

The Critter Express

Brand: B.toys Pages: 2

$VTech Quiz Biz Math Mania User Manual preview$

Quiz Biz Math Mania

Brand: VTech Pages: 13

Brand: Faller Pages: 12

Nick Jr The Backyardigans L2176

Brand: Fisher-Price Pages: 20

73510 Volkswagen New Beetle

Brand: Power Wheels Pages: 36

Brand: KDS Pages: 26

Lego 10283 LIGHT KIT

Brand: LIGHT MY BRICKS Pages: 47

LEGO STATUE OF LIBERTY 21042

Brand: LIGHT MY BRICKS Pages: 25

Brand: H-KING Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands