TANDBERG 770 User Manual Download

Page: 53 / 111

TANDBERG Videoconferencing System

Advanced use

Request floor

When requesting the floor, the MCU will broadcast your video in full screen to all other participants in the
conference. If the MCU conference has a chairman, a floor request is sent to the chairman.

You will remain ‘On Air’ until either you select ‘

Release Floor

’ or the chairman decides to release the floor to

another participant.

FLOOR

WILL

AUTOMATICALLY

REQUESTED

WHEN

SENDING

SNAPSHOT

SELECTING

THE

DOC

CAM

VIDEO

SOURCES

Release floor

You choose ‘

Release Floor

’ to take you ‘Off Air’. You should do this when you wish to make the floor available to

the other participants in the conference.

Terminal Names

Allows you to see the site numbers or name (if supported) of other sites connected in the conference.

View site # *

Allows you to view any participant in the conference other than the participant currently ‘On Air’.

End view

Allows you to stop viewing the site previously chosen with ‘

View Site #

’, and returns your view to the site that is

currently ‘On Air’.

* - NOT supported by the MultiSite

TIP

‘

IEW

ITE

’

AND

‘

IEW

’

CAN

USED

ALL

CONFERENCE

PARTICIPANTS

NOTE

Summary of Contents for 770
















































































































Search results

Summary of Contents for 770

Reviews:

Related manuals for 770

Brands by name

Popular brands

TANDBERG 770, User Manual

Search results

Summary of Contents for 770

Reviews:

Related manuals for 770

Brands by name

Popular brands