TANDBERG 770 User Manual Download | Manualshive

Page: 12 / 111

background image

12

TANDBERG Videoconferencing System

Installation

Connecting cables

1. Microphone cable

• Connect the microphone to the microphone cable.

• Connect the microphone cable to microphone input

1 on the system.

2. Monitor cable(s)

Scart (Europe):

• Connect the Scart adapter to one of the Scart

connectors on your monitor.

Scart (Europe) & RCA/S-Video (US):

Audio:

The cable with one RCA connector on one side and two

RCA connectors on the other side:

• Connect the two RCA connectors to your monitor (or

Scart adapter) Audio Left/Right connectors (the audio
signal from the system is a monaural signal and
therefore is fed into both audio-in sockets on the
monitor).

• Connect the other end to ‘

Audio Out

’.

Video:

• Connect the S-video cable to the S-video connector

on your monitor ( or Scart adapter). If you do not have
an S-video connector on your monitor, connect the
RCA-RCA video cable to the RCA connector on your
monitor.

• Connect the other end to ‘

Video Out

’.

TV/Monitor

Scart

converter

Connecting with Scart

DC in

1

. Single

2

. Single

Video out

Audio out

3

. Dual

3

. Doc

4

. VCR

VGA out

1

Mic

1

2

Mic

2

3

1

2

3

4

VCR

1

2

ISDN BRI

Ethernet

I

O

LAN

Power

ISDN 3
ISDN 2
ISDN 1
Mic

ONLY 1, NOT BOTH

TV/Monitor

Connecting without Scart

DC in

1

. Single

2

. Single

Video out

Audio out

3

. Dual

3

. Doc

4

. VCR

VGA out

1

Mic

1

2

Mic

2

3

1

2

3

4

VCR

1

2

ISDN BRI

Ethernet

I

O

LAN

Power

ISDN 3
ISDN 2
ISDN 1
Mic

ONLY 1, NOT BOTH

«
...
10
11
12
13
14
...
»

Summary of Contents for 770
















































































































Reviews:

No comments

Related manuals for 770

Brand: PACH & COMPANY Pages: 4

Brand: Panamax Pages: 16

Brand: Teac Pages: 60

Brand: DC-Connex Pages: 16

Brand: Hama Pages: 76

Brand: iRobot Pages: 7

Brand: Redback Pages: 16

VideoJet 400 19"

Brand: VCS Pages: 86

Brand: Sound Projections Pages: 2

Brand: texet Pages: 24

Brand: Aiwa Pages: 58

Mira Connect 10

Brand: Aveo Systems Pages: 2

Brand: Denver Pages: 12

Brand: Denver Pages: 32

Brand: Denver Pages: 52

Brand: Denver Pages: 79

Brand: Dual Pages: 32

Brand: Sapho Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands