TANDBERG 770 User Manual Download

Page: 15 / 111

TANDBERG Videoconferencing System

Installation

System configuration

• Switch the system on by activating the power switch on the system.

• After the system has performed a self-test routine, product logo and a ‘Welcome’ menu will be displayed on the

monitor.

connect

RESS

ENU

THE

REMOTE

CONTROL

. S

ELECT

THE

‘

ERMINAL

ETTINGS

’,

‘

ETWORK

’,

‘

ISDN-BRI

SETTINGS

’. S

ELECT

THE

RELEVANT

‘

INE

ETUP

’

AND

SET

‘

NABLED

: O

’.

• Enter System Name to identify the system during an MCU conference. Select ‘

Utilities

’, ‘

System Name

’ and

enter the name using the number keys (as on a mobile phone).

• Select the language you want to use in ‘

Terminal Settings

’, ‘

Language

’.

• If you are using two monitors, set ‘

Utilities

’, ‘

Dual Monitor: On

’.

• To activate MultiSite and/or Presenter, enter an option key (see paperwork accompanying your system), see

‘

Terminal Settings

’, ‘

Software Options

’.

• Press

ONNECT

on the remote control. A dial tone should be heard if the network is active.

• Using the monitor remote control, adjust the volume on the monitor to a level of your choice. This
volume will be the default volume for all calls.

HESE

SETTINGS

ARE

ESSENTIAL

FOR

OPTIMAL

SYSTEM

SET

NOTE

• Enabled but unused ISDN lines (lines not active) should be disabled. Select the Quick Key ‘

System Info

’ (on

the remote control) to view line status.

Summary of Contents for 770
















































































































Search results

Summary of Contents for 770

Reviews:

Related manuals for 770

Brands by name

Popular brands

TANDBERG 770, User Manual

Search results

Summary of Contents for 770

Reviews:

Related manuals for 770

Brands by name

Popular brands