Tanda AQUATOP Installation Manual Download Page 56 | Manualshive

Page: 56 / 239

Tanda AQUATOP Installation Manual Download Page 56

MAN-AT-C2-2

Manual Aquatop (2019)

4

5. Installation of the flange

•

Mark and drill the holes and fix the flange on the pool wall using the supplied bolts (8
mm). Use enough silicone in the fixing holes as an extra sealing.

•

The flange can only be placed after applying the wall cladding.

•

For pools with mosaic tiles, we recommend to have the flange mounted before the
mosaic tiles are being applied as such makes the installation watertight on the concrete
rather than on the mosaic tiles.

N°

Description

N°

Description

1

Flat sealing

3

Shaft end

2

Flange

4

Setting ring

6. Installation of the roller shaft

•

At non-motor side, insert the shaft end into the roller tube and fix the locking ring. The
shaft end requires to be screwed on to the flange. Then, insert the drive shaft through
the wall duct and connect it to the roller shaft. Do not forget to mount the protection
ring. ATTENTION : The connection between the drive and roller shaft is different for
120/250 and 500/1000 Nm motors.

The 4 rods drive the shaft !
The 2 bolts only take care of the connection between driving shaft and roller
shaft. Do not tighten bolts too much !
The 1000 Nm motor comes with a 42 mm driving shaft (instead of 30 mm).

5 mm ‘air’ between setting ring and shaft

500 Nm/1000 Nm Motor

Protective ring !

«
...
54
55
56
57
58
...
»

Summary of Contents for AQUATOP
















































































































































































































































Reviews:

No comments