Tanda AQUATOP Installation Manual Download Page 35 | Manualshive

Page: 35 / 239

Tanda AQUATOP Installation Manual Download Page 35

MAN-AT-A9

Manual Aquatop (2019)

1

A9 - Constructional preparations: Top’Moov

General:

▪

Level control is essential to be able to install and use an automatic slatted cover.

▪

Please do not place any obstacles which can obstruct the course of the cover.
E.g. skimmers, ladders, …

▪

The position where the supports are being fixed requires to be a flat surface
solid enough for anchoring.

▪

At these exact position of the supports, the slats will enter and leave the pool.
The coping stone cannot exceed the wall distance. In case the coping stones
will obstruct free movement of the slats, coping stones should be cut.

▪

If the Top'Moov is installed in an environment with much and strong wind, ask
for an additional brake on T & A

Rmax = 50 mm

«
...
33
34
35
36
37
...
»

Summary of Contents for AQUATOP
















































































































































































































































Reviews:

No comments