manualshive.com logo in svg

tams elektronik LD-G-32.2, Manual

Share
Download
tams elektronik LD-G-32.2 Manual Download Page 4

tams elektronik

English

LD-G-32.2 and LD-W-32.2

1. Getting started

How to use this manual

This manual gives step-by-step instructions for safe and correct fitting and
connecting of the decoder, and operation. Before you start, we advise you
to read the whole manual, particularly the chapter on safety instructions
and the checklist for trouble shooting. You will then know where to take
care and how to prevent mistakes which take a lot of effort to correct.
Keep this manual safely so that you can solve problems in the future. If
you pass the decoder on to another person, please pass on the manual
with it.

Intended use

The locomotive decoders LD-G-32.2 and LD-W-32.2 are designed to be
operated according to the instructions in this manual in model building,
especially   in   digital   model   railroad   layouts.   Any   other   use   is
inappropriate and invalidates any guarantees.
The locomotive decoders should not be mounted by children under the
age of 14. 
Reading, understanding and following the instructions in this manual
are mandatory for the user.

Page 4

Summary of Contents for LD-G-32.2

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands