background image

SAFETY INFORMATION

Some of the principles of this product’s safe installation and operation

are not immediately obvious. Read the following safety information

before continuing further:

• Never 

operate this fan without a window or door opened.

• This fan is meant for general ventilation.

 It has NOT been designed to ventilate particle laden and / or explosive mixtures of air.

• This fan is not for use in kitchens.

• Never  

force open the damper door(s), this could severely damage the actuator. 

Always 

depress the

actuator’s yellow clutch release before manually opening or closing the damper door(s).

(Drop Down Door only)

• Before installing or servicing this fan, switch power off at the home’s electrical panel to reduce the

risk of damaging circuit boards, fire, electrical shock, or injury.

HANDLING INSTRUCTIONS

   This fan’s aluminum construction is corrosion-resistant and   
    extremely durable. However, this fan should NEVER be 
    handled using any of  the Aerodynamic Wings that mount the 
    motor within the assembly. These Wings are highlighted in the 
    illustration. Always handle this fan by either its external 
    casing or the motor itself. You can also handle this fan by its 

hanging straps, but be careful as their edges are sharp.

SUPPLIES INCLUDED 

Prior to beginning installation, please verify all of  the following items were received with the fan:
• 2500 Fan Assembly. (see last pages for identification of  parts)
• Damper Assembly (Drop Down Door or Air-Door) (see last pages for identification of  parts)
• Duct Assembly with Duct Ring (Ducted versions Only, see last pages for identification of  parts)
• Cube-Core Grille (incl. 4 powder-coated wood screws) (If  the Ventura Air-Door was purchased)
• Adhesive-backed Foam Tape Isolator.
• Hardware Kit with square bit driver (incl. Screws / tape / strain relief  for interlock)
• Digital Touch Controller package—including one Digital Touch controller, one wall mounting bracket,
mounting screws and 50 feet of  red shielded CAT5 cable.
Once all received parts are verified, perform an operational test BEFORE installing it in the attic.
See pages 8 and 12 for connections to be made.
Note: 

ten

 second start up delay.

This is a good time to write down the serial number(s) on this 

manual

, which will save you a trip to the attic if

you

 

require Tech Support.

 Page 4

HV2800 Kaze/HV2800D Venti

 Whole House Fan Installation Manual, 

HV2800.

©

Tamarack Technologies,

 

Inc All Rights Reserved 20

20

Summary of Contents for HV2800 Kaze



















Reviews: