TallyGenicom 6306, Maintenance Manual

Page: 100 / 175

A
A
B
B
C
C
9
11
12
13
14
16
29
35
52 2X
62
2X
2X
63
54 2X
086088 ASSY
75 A/R
6
VIEW B-B
41
77
2X
2X
76
REF
REF
74
7
13
REF
REF
REF
14
11
VIEW A-A 6
39
4
FULLY
OPEN
54
REF
35
11
13
REF
REF
REF
41 REF
.152
VIEW C-C
76
12
CHASSIS
PROPRIETARY NOTICE
SIZE
TITLE
DWN
CHKD
PRE-REL
FINAL
MFG
Q.A.
C.S.
CHG BD
PART NUMBER
REVISIONS
SYM
APPLICATION
DO NOT SCALE DRAWING
12344
D
8 7 6 5 4 3 2 1
D
C
B
A
D
C
B
A
1 2 3 4 5 6 7 8
This document and the information contained therein are the
(1) use such information for purposes other than those expressly
authorized by TALLY; and (2) furnish such information
to any other person in whole or in part without the prior express
written permission of TALLY; and, to promptly return
this document to TALLY upon the receipt of a request
therefor.
property of TALLY. Recipient agrees not to:
QTY REQ
ITEM
NO.
PART NUMBER
TOLERANCES ARE:
UNLESS OTHERWISE SPECIFIED
DIMENSIONS AND TOLERANCES ARE
IN INCHES AND SHALL BE INTER-
PRETED PER ANSI Y14.5M-1982.
0.X ±0.1
0.XX ±0.01
0.XXX ±0.005
0.XXXX ±0.0005
ANGLE ±0°30'
THIRD ANGLE
PROJECTION
SCALE: NONE FILE NAME: 4076F SHEET: 1 OF 3
SHIPPING: 6020 So 190TH ST.,
KENT, WA 98032 USA
2. NUMBER WITHIN CIRCLE INDICATES ITEM OR FIND
NUMBER, SEE PARTS LIST FOR SPECIFICATION.
NOTES: (UNLESS OTHERWISE SPECIFIED)
1. MANUFACTURE, ASSEMBLE & PART MARK PER TALLY
WORKMANSHIP STANDARDS.
16-0001E-21
DATE DESCRIPTION
BY
APPROVED
DESCRIPTION MATERIAL FINISH
CODE IDENT DWG NO. REV
NEXT ASSY
MODEL REV SHT
-
A
B
C
D
E
F
1/10/04
4/8/04
5/3/04
5/26/04
6/6/04
7/1/04
10/1/04
YL
YL
YL
YL
YL
YL
YL
PRINT MECHANISM- BASIC,
6306
614076
F
086088 614077 6306 F 1
RELEASE TO PRODUCTION
REVISED PER DCR #31204
REVISED PER DCR #31338
REVISED PER DCR #31375
REVISED PER DCR #31395
REVISED PER DCR #31417
REVISED PER ECO #40199
TORQUE TO 6.0 IN-LBS.
TORQUE TO 2.5 - 4.0 IN-LBS.
4
5
TIGHTEN THE PLATEN MOTOR SHAFT SET SCREW AS
FOLLOWS (SEE VIEW A-A); MANUALLY ROTATE THE
PLATEN TO THE FULLY OPEN POSITION, WHILE HOLDING
THE PLATEN FULLY OPEN ROTATE THE PLATEN MOTOR SO
THAT THE SHAFT FLAT MATCHES THE ILLUSTRATION ON THE
PLATEN MOTOR SENSOR PCB, TIGHTEN THE RIGHT PLATEN
SET SCREWS.
6
9. ORIENT TENSION CLIP (ITEM 41) AS SHOWN IN VIEW B-B.
DB MBO
DB GAG
DB CB
DB CB
DB CB
DB CB
DB C2
7 IDENTIFY CONNECTOR NO. AS J26.
8 IDENTIFY CONNECTOR NO. AS J22.
3 TORQUE TO 5.0 IN-LBS.
11 THE SQUARE SHAFT SHOULD BE PUSHED INTO THE
COUPLER UNTIL IT HITS THE INTERNAL STOP, THIS
COMBINATION IS PUSHED INTO THE MOTOR SHAFT
SO THE SHOULDER OF THE SQUARE SHAFT IS AGAINST
THE END OF MOTOR SHAFT.
12 SPRING WASHER (ITEM 82) TO BE ORIENTED AS SHOWN.